KGST307HBS1 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Geri from Brand Haven, MI
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of the pads on the bottom of the grate kept falling off.
I was able to order the part I needed. The faulty pad had a broken stem.Several pads came in a bag so if I have the problem again I will have the parts on hand. I bought some RTV glue suitable for items at high temperatures; used a probe to make sure the hole in the grate was clear and clean and glued the new pad in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Wildomar, CA
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven temp not hot enough
Followed Mfgs instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doyle from Oly, WA
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would bake for several minutes then turn its self off. It would not come back on until you reset it. The time varied from 10 to 15 minutes before turning off.
I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Tyngsborough, MA
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet on gas stove top grates were gone
Very simple, cleaned out what was remaining of the old rubber feet and just pushed these in. I didn't bother glueing them in as I didn't feel they would fall out. If they do, I'll go out and obtain the glue that is mentioned by others in this thread. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Slidell, LA
- Parts Used:
- WP9781593
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
broken inner glass in oven door
ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jayne from Neptune, NJ
- Parts Used:
- WP9782065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat up.
Remove the bottom panel and confirmed that the igniter was not lighting. Unsrcrew the igniter from the housing in the oven, then removed the back of the range and unplugged two leads from their conections and ran the wires through the insulated back wall of the oven. To replace the part just did the opposite of above. Piece of Cake. Want to say also that I was astounded at the speed in which I received my part. Ordered it at 3:30 PM on Friday afternoon and received it by 10 AM Saturday. And with standard delivery! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Plainview, NY
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheel broke off oven drawer
I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitchell O from Williamsburg, VA
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven not heating to set temperature
Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.
Was this instruction helpful to you?
Thank you for voting!
broken interior glass in door
pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.
Was this instruction helpful to you?
Thank you for voting!
Oven Light bulb and gasket needed replaced
Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Fort Wayne, IN
- Parts Used:
- WP9781593
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The inside oven glass cracked down the middle
I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Houston, TX
- Parts Used:
- WP9782065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven would turn on but not heat
Looked online and found it was probably the igniter which wasn't firing. An incredibly gratifying and easy experience with the self-fix. Worked on the first try just like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chapel Construction from Caledonia, WI
- Parts Used:
- WP9782065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Range was operating intermittently.
The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Gettysburg, PA
- Parts Used:
- WP9782065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not light.
Open oven door. Remove covers from burner tube. Remove 2 screws holding igniter. Remove panel from back of range. Unplug 2 wires attached to igniter. Pull wires thru inside of oven. Reverse process to install new igniter.
Was this instruction helpful to you?
Thank you for voting!