KESH307HBL5 KitchenAid Range - Instructions

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

I have KitchenAid convection oven that is about ten years old . The hinge on the left hand side broke so I had to replace it. It took me about 2 hours to get the job done because I cleaned the door as I went . The change out while fairly strait forward did take some time . A lot longer the some of the people said .

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Followed the instructions in the video provided by PartSelect, which was very accurate. They only problem I have encountered is that the wiring from the old element compared to the new element do not match up 100%. I had to call Whirlpool today and schedule a Tech to come out and see if they can resolve the problem. Right now, when the burner is turned on, both the inner and outer elements turn on.

removed door from range and slowly took apart until reached inner glass. there are three pcs of glass, front and two inner. was able to clean the inside which was dirty after 15 years of use. took alittle over an hour from start to finish including thorough cleaning.

First BE SURE TO TURN OFF THE CIRCUIT BREAKER!!! Remove the oven door if you need to get closer to the work. Then remove the screws securing the the element to the the oven. There were two on each side in the back where the element goes they the wall and two more that held the element to the upper surface. Carefully pull the element out to gain access to the wires and terminals. Gently pull each wire off one at a time, being sure not to allow the wire to get pulled back into the rear part of the oven. Reconnect each wire securely to the new element. Doubly check each connection! Then replace each screw and you should be set!

Took the back off and put it in. It was a snap! Shouldn't have waited 1 year to do it!

Replaced damaged drawer roller: easy peasy!

This worked very well, thanks to the advice posted from other users. The only part that was a bit unclear was removing the door. There are small, slotted metal pieces screwed into the sides of the oven to hold the door hinges in the slots. After removing those, I had to hold the door and push it up and down, and a little bit side to side, to get the hinges to start sliding out, but they did. There are no other screws or brackets holding them in place. The hinges are on springs, so they do snap up when they come out of the slots in the sides of the oven. But they only snap to a 90 degree angle, so they won't cut your fingers off. You'd have to hold your fingers right on them to even get pinched. After that, I just kept taking screws out of the door until I got through to the back panel, replaced it, and put it all back together.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

The nylon roller was very easy to install. Although rather pricey for what the part was, it was shipped immediately and got the job done. Took all of 5 minutes to do. I wish all my repair jobs were that easy.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

ordered new broiler pan

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.