KERC600GWH1 KitchenAid Range - Instructions

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

Removed back panel on stove and found no continuity in bake element indicating a break in the element circuit. Also tested electrical supply up to the element and found that we had electricity up to the element when the oven was turned on. Went on line and ordered the bake element and it was on my doorstep in 48 hours. Remove 2 screws inside oven and disconnect wires from the rear and install new element and plug the 2 wires into it, replace rear panel ( 3screws) and turn electricity back on to the stove and you are back in business.

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.

I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.

We had been missing it for years. Perhaps it melted, maybe the dog. Anyway, Home Depot didnt have the match. I order the exact knob, received it in a very timely manner. Took it out of the package, and without any tool, placed it it it rightful spot. My wife is happy now. Thanks for helping me.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

slide the glass in. Thank you for having such a wounderful place to get what others said we can not get this glass. Thank you again

Followed Mfgs instructions.

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.

Removed top of stove replaced heating element ,piece of cake.

Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.

Removed rear panel (6 screws) and disconnected the four connectors on the Broil element. Then removed the 4 screws holding the the element to the top of the oven cavity. Inserted new element and connected the 4 screws to secure it. Connected the four connectors and re-installed the rear panel.