KERC507EBL1 KitchenAid Range - Instructions

ordered new broiler pan

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

This is a microwave/ Oven slide in unit. You DO NOT need to slide out the unit, the repair can be done from inside the oven. Just be careful on pulling the wires from the unit so they do not break. I used shrink wrap over the joints but you can use tape as long as it can take the temperatures

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Thanks for the previous viewer's tip, disconnect power, pushed the cook top out of the counter and used a wood block for the support. Unscrew the smooth top from the burner, remove old and plug in the new one. Connect power, test OK. Put everything back.

I removed the door and I took it completely apart in order to replace the broken inner glass pieces. The door has about 30 separate pieces, so it is a meticulous repair and I recommend that you be fairly handy if you are going to attempt this. Something that seems as though it should be pretty simple took me nearly two hours to complete. I am happy to report that the result was a resounding success. The broken oven door glass had been affecting the oven temperature and as the result the baked foods were adversely affected. Cakes, pies, etc, would either be over or under cooked with no way to properly regulate the temperature. The inner glass is necessary in order to maintain correct oven function, so replacing it made everything work as designed once again.

It was difficult to reach the back of the oven inside to remove screws. I had to use an extended socket with a bit tip. When I tried to remove the element from the clips, the clips slid back inside the insulation at the back of the oven. I had to take the back panel off of the oven, push the clips through the opening and then I used a bag clip to hold them so they would not slide back into the opening. I could not lift the door off-too heavy- to get closer to the back of the oven to put the clips and screws back on so I laid the oven on its back after putting the back cover on. The oven door was so heavy then that I had to prop the oven door open with my 24 inch rolling pin. I then leaned down into the oven and managed to get the clips and the screws back in. I then put the oven upright again, plugged it in, then had to re-level the whole thing. I turned it on and it worked. This probably would have been easier if I were not 65 years old and had some help. I was not giving up though. I got it done.

Had difficulty removing the two screws holding element(range is eighteen years old.Screws were badly rusted)After that,it was a piece of cake

TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.

Turned breaker off. Removed oven door for access, two screws loosened element, unplugged wires from element & removed element. Reverse order to install. Perfect fit. Thanks.

Remove two screws. Plug n play.

Had to screw off old terminal block & screw on new one

Replaced both rollers....Quick and Easy!!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

The repair was simple:
PartSelect always seems to have the parts you need and they get them to you quickly.
Baking element - I removed the two screws that hold the element to the back of the oven ( Philips head). Disconnected the spade type electrical connections from each end of the element. Note: use some type of clamp to hold the wires from pulling back into the outer section of the oven. I used wooden clothespins). Reverse the process to install new element.
Broiler element - I placed the shipping container over the new baking element to protect it. Then removed the four screws holding the top element to the back of the oven ( Philips head). Take care to mark the 4 wires for the broiler element. ( 2 for outer coil & 2 for inner coil) Clamp these wires also after disconnecting. Slide the 2 "L" shaped hangers out of there slots. When installing the new element connect the wires first then slide the "L" shaped hangers back into the slots. reinstall the 4 screws and your done. I did the repair with out removing the oven door ( ours is difficult to get back on ) with the door off the job will take less time and access will be easier.