KGST300HWH9 KitchenAid Range - Instructions

Replacing an oven igniter is one of the easiest repairs you can make to your oven. There are two igniters - one for the broiler and one for the oven itself. Oven Igniter: Start by removing the rear panel of the oven which attaches with a couple screws. Inside the oven, remove the "butterfly" shaped heat deflector (over the flame tube) which attaches with four screws. You now have access to the igniter. Remove the two screws which attach it to the bracket. On the rear of the oven, unplug the two spade connectors. Pull the igniter out from the front of the oven. Fish the wires for the new igniter through the same hole. Plug the 2 new wires back in. You can't mess this up - the wires have matching connectors and you can't get them confused. The broiler igniter is a little more complicated. You will have to remove the side panel of the oven to reach one of the connectors. It's just a couple more screws. The procedure is the same, but the wires are much harder to "fish" through the hole though. Unscrew the broiler igniter from the bracket and unplug the wires. Before you pull them out, attach a length of clothes hanger so that you pull the hanger into the oven from the rear. This way you can attach the new wires to the hanger and then pull them through to the back of the oven. If you don't attach something when you pull the old wires out, it is very hard to fish the wires for the broiler igniter to the rear of the oven. Good Luck!

As a relatively handy person, I have built homes, and done every kind of repair you could imagine from plumbing to heavy construction. I never wanted to play with appliances, just couldn't read those diagrams well enough to feel comfortable. Parts select has changed my life and saved me so much money and I have repaired appliances in several of the homes with no issues using your videos and parts as my guide.

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

Per the instructions listed in your customer replies

Replaced valve, 3 pipe connections 4 wire connections, still did not work, small flip up valve was set at off position, set to on, still did not work, replaced ignitor, bingo that was the real problem, reinstalled old valve, still working fine; returned new valve assembly for full refund! Thank You

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.

I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the glass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!

The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.

pull out the stove,took the top back panel off, take off wires one at a time on new spark module.. easy

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

Looked online and found it was probably the igniter which wasn't firing. An incredibly gratifying and easy experience with the self-fix. Worked on the first try just like new.

Open oven door. Remove covers from burner tube. Remove 2 screws holding igniter. Remove panel from back of range. Unplug 2 wires attached to igniter. Pull wires thru inside of oven. Reverse process to install new igniter.

The stove burners and oven broiler worked fine so it was obviously something with the oven ignition. My oven is 14 years old so it made sense that the ignition would wear out. I followed the instructions provided on the PartSelect website for this repair and it worked perfectly. Very easy fix!

Removed the door. Took out all the screws. Removed the glass that was cracked. Put in the new piece. Put the screws back in place. Put the door back on and it was a done deal.