91192408992 Kenmore Range - Instructions

I simply turned the power off and slide the stove forward to give myself room to get behind it and just unscrewed the cover behind the burner switchers and pulled the switch knob off then I removed the two small screws that hold the burner switch to the control panel and go to the back and pull the wires carefully and replace them on the new switch one by one and screw the new switch to the control panel and replace the back panel and done!

I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR

replaced Plastic Guides

Ordered the part, it arrived and 5 minutes later it a complete installation

I removed the two screws that hold the element, then I took the back cover of the range to have access to the wires, after that, I took the old one out, placed the new one and finally hooked the wires and placed the two screws right back. Very easy. I thought about bringing someone to do the job, and after I was done, I couldn't believe how easy it was.

Just removed the old racks..and replaced them with the new racks...That's all...

I had read some of the other comments about the repairs. The one that I found most useful was the one describing how short the connector was once they are removed. That isn't a joke about 3/4". My sujestion is to have tape and tape them to the back of the oven so as to not to loose them in the insulation. Once that was removed and reconnected the oven worked again like new. Even the most novice of people will find it a breeze.

Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one

removed 2 screws that hold the cover in place, inserted the new panel at the bottom, pushed top in place and reapplied the 2 screws.

popped the new one on!

This oven is 2 years old and the element should not have broken like it did. GE is doing something wrong in the making of their ovens.
My husband took out the old broken element and attached the new one.

Mice took over trailer, after eliminating mice, and cleaning oven and range thoroughly, I noticed that the only place the mouse urine smell was still coming from was the vent tube. Noticed soiling around tube where it went through and into oven. I removed the center rack, layed some foil to catch any debris that may fall from the tube when it is removed. I removed old vent tube simply by removing the two nut screws on the roof of the oven. I had to pry it out a little bit. I then cut out and soiled insulation with razor knife, I inserted the new vent tube from the inside, and replace 1/4 nut screws and tighten.

Being that the rest of the stove was functioning fine, it was still plugged into the electrical outlet, after unplugging the range, I used a nutdriver and and removed the back panel exposing the two electrical clips on the old heating element. After unplugging the two electrical clips, I removed the two screws that secure the heating element to the back of the inside of the range. Once the screws were removed, the heating element came right out. I inserted the new element, installed the two screws previously removed, plugged the two electrical clips on the back of the heating element, re installed the back panel, plugged the range in and cooked lasagna. Total repair time was 12 minutes.

unplugged stove-removed cover in back of stove-unplugged element-inside oven removed two screws-removed element. reverse procedure to install. took about twenty minutes.
wife happy again.
parts came in two days. I could not believe how fast it came. Thank You very much! Jim Jewkes

Just put 2 screws in. It was simple.
Web site very good details for finding parts.
Fast turn around from order to delivery.
Very satisfied!!!