99151 (1988) Kenmore Range - Instructions

Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)

1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.

The terminal bloctk silver attachment did not fit our stove. We had to use the old one and take off a little of the nipple that snapped it into place .used a bench grinder for that.The rest was easy. Used a heat gun paint stripper to shrink the shrink wrap,Saved a big repair bill.

Easy

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.

Everything was very easy: identifying the right part was very easy on the website, the part came quicker than I expected, and my wife replaced the stove element before I even got home from work. She just pulled the old one out like she would to clean the top of the stove, and put the new one back in. Have had several awesome cups of coffee since the replacement.

The hardest part was working in the oven.

Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals with vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.

Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.

Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.

Did it By Hand
Your Shipment Time Excellant
Order it Mon. Received it Wed.


Thank You

I removed the old element and replaced it with a new part. It was very simple.

The power was turned off. The elemnt wiring was removed. The new one was installed in reverse order. Power back on and the oven tested just fine.

Had to take back panel off of the inside of the oven to get to the screws to remove the old element and attache the new. Removed the two screws to remove the old, pulled it out unattached the wires and attached the new one.

I first removed the two hex head screws, pulled the element slowly forward about four to five inches and disconected the two wires on the old element.
I removed the old element and attached the wires to the new element. I then slowly pushed it back into the rear wall of the oven, carefull not to disturb the insulation around the opening and replaced the two screws that hold the element to the back wall of the oven. It was easy enough to do, even for a woman. I turned on the oven and it worked great. No problems so far.

I pulled out the old burner - put the new one in and I was done. No tools required.

The first burner I received from PartSelect was warped. I called on Friday morning to see about returning it and ordering a new one. The CSR was very helpful and I was totally surprised to have the replacement arrive the very next day since I didn't ask for a Saturday delivery. I will definitely use PartSelect again.

Turned off power. Removed oven racks. Removed the 2 screws that held the element in place. Pulled element out about 3 in. & disconnected 3 wires. Placed new element, reconnected 3 wires & reconnected the 2 screws that hold element in place. Turned power back on & it works great!!. Was very pleased at how easy it was & also how fast I received the part, which was day after I ordered it.

First shut off power to the store and used a socket set to remove 2 screws and disconnnect the element. Connected the new element but had to use the old screws as the new ones did not work with my appliance.

First, I removed the burner from the box and plastic bag. Second, I pushed the burner into the socket and that was it.
I also want to comment on how easy the ordering process was. I ljust love this website. All you have to do is type in the model number and up comes all of the parts associated with the appliance. My order shipped the next day and I had unit within 2 days. Also, the part cost $42.00 with shipping. My local parts place was $48.00, so I wound up saving $6.00 and did not have to leave my home to buy it. I will definetly use this site again.