9119250799 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eben from Fort Worth, TX
- Parts Used:
- WB56T10037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Glass door shattered completely!
The biggest mess is getting ALL the glass cleaned up, and especially clearing the channel that the new glass sits in. After that, very straightforward - Unscrew door from exterior frame, then handle from frame, then seat glass on lower rim and carefully refit the frame and handle to the glass and tighten everything back up - Good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Colorado Springs, CO
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Burner went to "HI" after control knob turned past "MED"
Removed the screws holding the back in place, then pulled off the control knob and removed the two screws holding the infinity switch. Swapped the leads from the old to the new switch and reinstalled everything. Worked like a champ!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erin from THE WOODLANDS, TX
- Parts Used:
- WB56T10037
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
The glass was broken
Took off the screws inside the door then took off the screws under the handle. Aligned the glass and replaced everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bonifay, FL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Replace stove top burners (3 total)
Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Shenandoah, PA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
back burner not getting hot
unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Keystone Heights, FL
- Parts Used:
- WB44T10009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out
TURNED OFF CIRCUIT BREAKER FIRST. Pulled Stove from wall, Removed 5 screws to remove back plate. Unplugged 2 spade electrical connections. Unpluged temp. sensor plug. Opened oven door and removed 2 screws holding element to top of oven. removed screw holding temp probe to element. Installed the elment in the reverse order starting with the temp probe. when finished with install, I tested the unit before covering the back. I used a oven temp tester to make sure that when the element went out that the temp probe was not damaged. Everything checked out fine and I finished installing the back cover and putting stove in place. Cleaned up area and JOB DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from WEST PALM BCH, FL
- Parts Used:
- WB44T10009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
replace broiler element
First, UNPLUG OVEN. Then, remove oven door and place stove on work bench! JUST KIDDING!! Honestly, the repair would be easy if that were possible.The hardest part is kneeling, standing, hunching over, twisting your body holding flashlight in your mouth, etc...THEN, trying to re-attach wires screws etc. The repair is straight forward. unscrew all screws holding element in, pull element out about 6 inches, detach wires, and re-attach. Simple right? Maybe if you're 1 foot 2 inches tall or have 6 foot arms
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Birdsboro, PA
- Parts Used:
- WB44T10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Had to replace the broiler element
Removed the old element with a nut diver and put the new one in. Very simple instalation.
Amazingly the part arrived in just two days...
My T-Bone steaks are cooked just the way I like them again.
MikeS, Birdsboro, PA
Amazingly the part arrived in just two days...
My T-Bone steaks are cooked just the way I like them again.
MikeS, Birdsboro, PA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from West Lake, OH
- Parts Used:
- WB44T10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Bottom element burned up and it was a little scary. Never seen this happen.
Un plug the power first.
Took the old element out and removed two nut holding the element in place. Remved back access panel on the back bottom of the unit. Disconnected wiring to part pulling the clip off of the connector.
Done fixed saved the house call.
Took the old element out and removed two nut holding the element in place. Remved back access panel on the back bottom of the unit. Disconnected wiring to part pulling the clip off of the connector.
Done fixed saved the house call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from TEGA CAY, SC
- Parts Used:
- WB44T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Lower Element Open
Removed the 2 screws on plate. Pulled wires forward. Simply detached slide on connecters and inserted new element. Pushed back and installed plate. Dont forget to unplug the 220 volt. Though open can ground wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Huntington, IN
- Parts Used:
- WB44T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Bake element wouldn't heat
Removed the two screws that hold the element in place, then I disconnected the two wires and pulled the element out. I ordered the part and received it within two days. It was very easy to install. My oven was tunning in less than half an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Glen Cove, NY
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
switch went to high setting no matter what the setting was
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margaret from hastings, NY
- Parts Used:
- WB44T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element
took 2 screws out of the element, then too the back off pluged in the element replaced two screws done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John H. from JACKSONVILLE, NC
- Parts Used:
- WB24T10025
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Front right burner would obtain the right heat setting.
Went to You Tube, found the appropriate segment. "Wa La" the problem was solved. Burner is working the way it is supposed to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from CEDARVILLE, OH
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
When the burner was turned on it would be on high for any setting. In fact, the burner would be warm to touch even when the switch was in the off position.
I turned the power off at the circuit breaker, pulled the stove out from the wall, and removed the plug. I removed the top back panel, and took the burner switch out by unscrewing the 2 screws in the front of the panel. I used pliers to remove the wires one at a time from the bad switch and put them on the good switch. I replaced the new burner switch on the front panel and also, replaced the back panel. I put the plug back in the socket, pushed the stove against the wall, and turned the power on at the circuit breaker.
Was this instruction helpful to you?
Thank you for voting!