79093553301 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- angela from lake placid, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the bottom oven element shorted and melted
pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the computer board, and then the unit worked, with our new element that we replaced!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Warsaw, VA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken lens over oven light
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from KALISPELL, MT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The elements were not heating up
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Andrews, SC
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
switch had a diffirent lug configuration
made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from FRIDLEY, MN
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Element burned out.
Turned off power at the circuit box. After locating 1/4" nut driver (the hardest part of the repair)I removed the oven racks. Took the opportunity to wipe out oven. Removed the two screws holding the element in place.Pulled element out gently to expose the connections. Wiggled the terminal connector off the terminal on element. Gave the wire a little bend to keep it from pulling back into frame. Repeated process on other side. Removed new element from wrapper. Placed element on oven floor, reattached terminals--making sure they were on snuggly--carefully slid terminal ends back though slots in oven body. Lined up brackets, reinstalled screws, replaced racks and turned power back on. Turned oven on it worked. Made cookies! Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garland Futrell from CHESAPEAKE, VA
- Parts Used:
- 5304503232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Broken ; oven door inner glass
Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from HENDERSONVLLE, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Easy as could be
2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from N MYRTLE BCH, SC
- Parts Used:
- A316222301, A316222201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
showing age
bought drip bowl from big box store and the 8 inch did not fit . yours fit perfect will use you for future diy jobs thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine H. from SEAL BEACH, CA
- Parts Used:
- A316222301, A316222201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
crummy chrome drip pans were worn out. replaced wtih enamel ones.
I just pulled the old ones out of the sockets, cleaned underneath, and replaced with new ones. No-brainer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Demoris from GOLDSBORO, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
element burnt out
purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from OMAHA, NE
- Parts Used:
- 318228310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lenses wore down and broke off making the actual indicator lights fall down behind the control panel since the lights connect to the lens.
Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from LANOKA HARBOR, NJ
- Parts Used:
- 318372210, 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I damaged surface element left kettle on without water in it
The repair was really easy. All I did was unplug the surface element and plug in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from BRISTOL, VA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The oven bake element developed a hot spot which failed shortly after the hot spot developed.
Unplug the stove or disconnect at the breaker. Open the oven and remove the bake racks. Using a nut driver (or Phillips Screwdriver) remove the screws (one per side) that secure the bake element. Place them in a safe/secure place outside of the oven. Carefully pull straight back on the element until about 3 inches of the wire, that connects to the element, is exposed. Carefully unplug the wire from each element (make sure that the wire does not pull back into the oven insulation. I placed a small metal clip on each wire). Remove the old element and plug the new one in. Put everything back in the exact same way you took the old one out. Power the oven up and preheat your oven. Monitor this - should be no problem at all. Very simple process. My first attempt at this and it was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from GAINESVILLE, GA
- Parts Used:
- 5304524341
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)
Was this instruction helpful to you?
Thank you for voting!