62920236 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Billy from Twentynine Palms, CA
- Parts Used:
- WP5700M600-60, WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Installed new fiberglass gasket and glass window
I removed about 8 screws to disassemble the door to get the gasket in. This was an easy task. On the first use of the oven, it shattered one pane of the double glass door window. I think I installed it backwards since one pane is tempered glass, I believe. I installed the new window and am heating it up now - hope it doesn't break.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Westford, MA
- Parts Used:
- 12200039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
fan/light switch broke
- the fan/light switch was still functioning, but it fell into the cavity underneath, after years of use, heat and grease caused it to weaken.
- 4 wires came off the old switch, and went on the new one with ease.
- the only complication was in getting the clips off of the old ones, and getting the new clips onto the new one. otherwise, a piece of cake.
- 4 wires came off the old switch, and went on the new one with ease.
- the only complication was in getting the clips off of the old ones, and getting the new clips onto the new one. otherwise, a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Poulsbo, WA
- Parts Used:
- WPY04100019
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Baking element went out
The hardest part of the repair was getting the old cruddy screws out of the old element. They were sort of "baked-in". Once we got the screws out the rest was really easy. Just inserted the element prongs & screwed the new ones in. Ordering & receiving the part was a snap...I would recommend your company to anyone. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gwen from Memphis, TX
- Parts Used:
- WPY702338
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Seal was badly damaged on door of 24 year old range.
Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.
We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.
We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Wells, ME
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner got excessively hotand couldn't be regulated
The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Foxboro, MA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new filter
Replace filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shaker Hts, OH
- Parts Used:
- A405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken vent cap
Unscrewed old cap, installed new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Holyoke, MA
- Parts Used:
- WPY04100019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
low and erratic temperatures
remove two screws, pull out element, diconnect two wires, toss old element,plug in wires to new element, replace two screws and viola- done
Now if you just sold faucet parts I'd be all set.
Now if you just sold faucet parts I'd be all set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Minden, LA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
eyes burned out on old cartridge
Simply unpluged the old cartridges and plugged in the new ones, it could not have been easier. My 18 year old cooktop looks brand new. My old cartridges were black and the new ones are stainless, but, the look is good, since most new appliances are now stainless. The best part is that it cost less than half of what a new cooktop would have cost plus all of the mess that would have been made tearing out the old one and installing a new one. Thanks PartSelect, A Very Satisfied Customer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT L from SUSSEX, NJ
- Parts Used:
- WPY04100019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element arc'd
needed hammer to help loose screws .pulled out and replaced leement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Royal Oak, MI
- Parts Used:
- WP7403P899-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Oven stopped heating
I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William D from Edinburg, TX
- Parts Used:
- 12200039
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan/Light switch worked for fan but not for light
The job was easier than I thought it would be. Turned off power at breaker first! Used phillips screwdriver to remove 2 fairly tight screws located on the vent side of the switch mounting plate. Flipped over plate and wrote down the 4 spade tip wire colors and location on switch. Removed the wires from the switch and removed the switch by prying off the locking washer with a sharpened/filed thin putty knife to get under it and then a flat blade screwdriver to finish removing it. Put the new switch in, hooked up the spade tip wires, mounted the plate back on and turned on the power. Worked great and I even impressed my Wife!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from montgomery, NY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
No leveling legs
Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve
Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Columbus, OH
- Parts Used:
- 12200039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
toggle switch for fan/light had melted from a hot pan placed on it (presumed)
Installing the new switch was EASY. However, removing the old switch was very difficult due to the nuts holding the switch in place being designed as clamps not threaded screws and nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerard P from Poughkeepsie, NY
- Parts Used:
- 12200039
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Housing of fan switch broke causing the switch to be inaccessable to use
After accessing the switch and removing the wires(four wires as the rocker switch operates both fan and oven light) I attached the wires to the new switch. However , I was unable to mount the switch in place as I could not get the spring - clip type of fasteners to slip on.
Fortunately, there was space to drill a hole on each side of the switch and I used brass machine screws
and nuts to hold the switch. The round-head screw
tops show on top of the stove, but at least the new switch is in place and operating.
Fortunately, there was space to drill a hole on each side of the switch and I used brass machine screws
and nuts to hold the switch. The round-head screw
tops show on top of the stove, but at least the new switch is in place and operating.
Was this instruction helpful to you?
Thank you for voting!