22314 ((1988)) Kenmore Range - Instructions

1. Killed power and removed the regulator's knob, noted the position of the old control.
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.

(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)

Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).

Bought a new house last fall. Jenn-Air range had two element cooktop with two element grill. Oven went out and while service man was here, I asked him to check on the price of another two heater element panel to replace the grill. He subsequently called to say the part I wanted was not available. I immediately got on the internet and did a search. Found it "ships same day" for what I thought was a very reasonable price at PartSelect. Unplugged the grill and plugged in the cooking plate. We now have four usable "burners" instead of two. Thanks PartSelect!

Removed element and installed new one

Removed old ones and plugged in new ones.

One of my new burners went bad about 6 months later and it was so easy to get a new one sent to me, at no cost even though the price of the burners went up. I received replacement within 2 days. Great service and my salesperson was great!!!!!!

Simple Repair!
Turn off Power
Remove four screws under panel.
Remove old burner knob.
Drop Burner Panel from range
Remove 5 wire connectors from old burner control
with pliers
Remove 2 screws that held burner control to range
panel
Install new burner control
Rplace two screws to burner control
Replace 5 wire connectors to new burner control
Replace 4 screw under panel
Replace knob to new burner control
Turn on electricity
Made wife happy!

I ordered replacement burner cartridge. Pulled out non-functional burner cartridge and installed new cartridge. They are plug in units so no tools were needed and it only took about 15 seconds. Took longer to get cartridge out of shipping container than it did to install it.

New black unit looks different than 15 year old unit but works better and looks better. Black granite appearance is more modern looking.

I should add that the old unit had been in place for approximately 15 years. It didn't come out when I first was trying to remove it to get model number and serial number from it. Once the old rust and corrosion was overcome it removed and reinstalled as easy as any electical plug in a wall outlet.

Remove and replace with new. No tools required.

This is fantastic. We've had this Jenn-Air range for some time now, but we only used the two-burner module on one side and the indoor grill on the other. Less than a week before Thanksgiving we decided that the extra two burners would be very useful, so I set out to search the internet for a good deal and the possibility of getting it before needed. Then I found your website and within minutes theunit was on the way and, at the most reasonalable price available. I recieved the unit he next day. All I had to do was plug in the module and it was done.
Thanks for making life easy

Unplug old burner assembly and plug in new one

The replacement switch was not exactly as my original and none of the other instructions matched exactly with my unit. So I had to figure it out, but they matched mostly what Micheal from Colliervile wrote. Safety is paramount. Turn off circuit breaker and ensure there is no power to unit with a test light. You don't have to remove the glass top. Open oven door and remove 4 screws at bottom of control panel, then remove two screws on each end while suppoting the panel with one hand. Rest control panel on top of door or hang by wires. Remove two screws to detach switch from panel. I took pictures of the wire placement on old switch and drew a diagram of what color wire went to each terminal. I used the instruction sheet diagram of new switch and marked where each wire color goes. Here is where I put them: DOUBLE BLACK to L1,2; New jumper from P1 to S1; RED to 2: DOUBLE RED to P2; new jumper with small connector from S2 to "element on" indicator lamp (it's longer than and replaces existing jumper); YELLOW to 4a; TAN to 4. The letters in parenthesis on the instruction sheet almost matched up to my old switch so I used them to help with the placement. I didn't have to seperate any compound red wires. Double check wire placement and put it all back together in reverse order.

pull out the grille element and replace with cooking element

First step is turn the power to the range off. Then I removed the grate covering the down draft vent in the center of the cook top. Inside the vent opening are two screws that secure a panel that holds the four knobs that control temperature settings. Remove these screws. Slide the panel tward the back of the range while lifting it up. This will allow removal of the panel. Remove the knob from the burner control you are replacing. Under the knob are two screws. Remove the screws and let the controller drop out of the cover panel. Take the new switch and carefully remove the wires from the old controller and place them on the new controller in the same position. When the wires have been connected, put the controller back in the control panes and secure it with the two screws. Replace the panel back into the cook top. Tilt the control panel so the front is low and the back is elevted. Engage the lugs protuding out on each side of the control panel opening. Lower the panel back into the opening and secure it with the two remaining screws. Replace the control knob and you are done. You just saved yourself a $125.00 service call. Total cost for the controller $35.00.

Each cartridge unit consists of two electric coil burners in a larger frame assembly. The old cartridge units simply lift up and unplug from the range top. The new units simply plug in and drop into place. It probably took more time to unpack the box than to remove the old, and insert the new cartridges. Anyone can make this repair, which instantly converts an old range top into a new one.

Pulled out old element and inserted new one (approx. one min.)

After discovering that the Jenn-Air cartridges unplugged from the stove, it could not have been more simple to order a new one from PartSelect (it arrived in two days), unplug the old cartridge, and plug in the new one - and no tools required!