79071533401 Kenmore Range - Instructions

Remove the oven drip pan & burner baffle. unscrew & cut leads to remove old igniter. Splice old leads to new using furnished wire nuts and remount. Job would have been easier with oven door removed, but didnt want to create a new project.

I exposed the ignitor through the inside of the oven and then removed the two screws that held it in place. I then cut the wires underneath the stove ans reconnected them to the new part with the wire nuts provided. It was a simple repair.

Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.

took drawer out, removed tin covers, found igniter and removed,snipped off parts to put on new igniter ,wirenutted old to new put back together ,we had ignition! all in all pretty easy job! detailed instructions that came with new part were easy to follow and precice

1. Unplugged power cord.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.

followed the instructions that come with the part. very quick and easy.

Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean in there MUCH better.

pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.

had the gas company do a free inspection.he told me the igniters go bad over time,so i went online with my model #and found a symptom/remedy page at part select.it said replacing the igniter fixed the problem 100% of the time.that gave me confidence and i ordered it,installed it and fixed it for $53.00(the gasman said most plces charged $250-300 to fix it.i was proud of myself-1st ever oven repair=great job!!! thanks.

Replacing the faulty ignitor would have been simple enough if my arms were a foot longer and the bolts that secured the old ignitor had not been baked on.

With an ample dose of WD40 and some Vise Grips I finally got them broke loose. An Ohm meter can tell you pretty quickly if the old ignitor is bad. My old ignitor measured more than 1 mega ohm while the new ignitor read only about 346 ohms.

1st took out switch from thermostat unit, located right on the other side of where the temperature knob is located (that controls cooking temp of the oven). Had to lift up range cover to get to the thermostat. Tested this switch with a meter and found it was OK. This made me suspect the igniter, so I ordered one.
To install I first unplugged oven (to prevent getting shocked) then took off the drawer on the bottom compartment (push in on tabs on rails until they release). Then take out two screws holding igniter. Mark wires with tape so you know which one goes to the upper part of the igniter and which one goes to the lower part. Then cut wires as close to the body of the igniter as you can so that you have plenty of wire to work with. Then hold igniter in about the place it will be mounted and mark the wires on the new igniter where you want to cut them. Leave a little extra so you have wire at a length that is easier to work with. Scrape off 3/8 inch of insulation off the end of each wire and connect the wires with wire nuts. Re-mount igniter. Put drawer back in. Plug oven back in and try the oven. I hope it works. Mine did thanks to God. Take care.

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconected the two wires. Take the old element out, and attach the new one. Assemble in reverse order.

took off bottom pan in oven and replaced ignitor