6644428914 Kenmore Range - Instructions

First I removed the two screws that hold the element in place with a 2' Phillips Head. I then pulled the element out about 3 inches and disconnected the two wires, with nose pliers, since they were semi-hard to remove the male from the female terminals.
I placed the order over the computer and it arrived in 2 days.
I was very pleased with PART SELECT.

Grabbed my courage with both hands, then with my other hand I used a screwdriver. Delicately removed 2 screws holding the broken element. Once that delicate operation was done, I took out the old and place the new. Once again grabbed the screwdriver and with agility replaced 2 screws. Then, I turned on the oven and Voila, ready to bake some enchiladas.
Winner, winner, chicken dinner.

On Saturday night before Thanksgiving my Wife indicated the oven was not heating up. A quick continuity check of the element indicated the unit was burnt out. I got on line and found PartSelect, found the proper element and ordered it. On Wednesday the element arrived and I removed the oven racks, removed two screws and pulled out the element to access the terminals. disconnected the wires, reconnected the wires to the new element and reinstalled the screws. Entire time was less than 5 minutes.

Thanksgiving dinner was saved at a reasonable price.

Unscrewed the two screws that held the old element to the back wall of the overn. Pulled out to reveal the two wires and connectors. Disconnected the two wires and removed old element being careful not to let the two wires recede back into the wall of the overn. Took the new element and connected the two wires. Then screwed the two screws through the holes in the element into the back wall. Easier than I thought it would be.

My husband undid the screws of the element. I went to Home Depot and they said I had to order in online. I could not find the part of the Home Depot website, so I googled the part and your business was easy to locate and order the part. It arrived in two days and I, the wife, was able to rescrew the element into place and, voila, the oven was functional again.

Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.

I took out 2 screws and installed new element! It took 5 mins.

I unscrewed the two screws holding the element in place and disconnected the two wires. Removed the element from the oven and replaced with the new one. Plugged in the two wires and replaced the two screws that secures the element to the back of the oven. Turned on the oven to test and turned back off when satisfied everything was O.K. Easy job.

Removed 2 screws on heating element mount plate. Pulled out heating element 3 inches and used needle nose pliers to remove the 2 connector clips. Reconnected connector clips by hand to new heating element. Put heating plate back into original position and reinstalled 2 mount screws.

Funny, I suppose. We decided to buy a new stove given the old age of the old one. Problem is, on delivery day it wasn't delivered and we discovered that there wasn't even one in the warehouse. At that point we got ticked and decided to look into the problem. The website led us right to the problem. We ordered, the part arrived the next day and the replacement was simple. Just unscrew the holder inside the over, unplug the old element and plug in the new. I needed needle nose pliers because one of the wires slipped behind the insulation. We also bought a thermometer and found that the calabration was right on the money. Happy campers... we saved $400.

Found breaker box and shut off power to stove, Check to make sure you turned the right breaker off before you attempt to put you hands in it, also make sure all the switches on the stove are in the off position . Open Oven Door, I used a Phillip screw driver to remove the two screws holding the Bake element in place . pull out to reach wire connections and gently pull connectors from element. Remove the old Bake element and Install the New one,by reversing process in removing the old one. after you have it back in place turn breaker back on at breaker box turn oven control to Bake setting, turn Oven Temperature control to around 200 degrees and Element should began to glow bright orange, job complete, it's that easy!~

Unplug oven unit from outlet or flip the breaker to disconnect the electricity. Used screwdriver to remove face cover, pulled wire connections from posts of old bake element. Attached wire connections to posts of the new bake element(they just slip on the posts). Aligned the face cover flush with the oven wall and replaced screws to hold cover on. Reconnect electricity and ready to bake. It is very simple.... We were very pleased with how quickly the element was delivered after ordering it.

I just removed two screws and disconnected the push on clips I then cleaned the botton of the oven and replaced the element. And it works just like new.

removed racks and door (could have left door on but made it easier to reach screws) removed 2 screws from old element unplugged the 2 wires and reversed process for new element.

I had no instructions, so I started by removing the two screws that seemed to hold the element together. I pulled the element forward and realized I had to seperate the element from the wires. It was an old unit so it took a strong tug but it did come apart. I was hoping at this point I was doing the right thing...I reconnected the new element , pushed it back in and replaced the screws. I was very impressed with myself! The new element heated up in no time. Yeah me!
Thank you "Part Select" for making it possible.