36272676790 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from BELLEVUE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- noreen from flushing, NY
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed extra oven space
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonel from Biddeford, ME
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven would not maintain set temperature
No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mchael J. from Chesterfield, VA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven post mini explosion sounding
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Greentown, PA
- Parts Used:
- WB19K36
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
Oven burner would not light.
I thought that when the burner didn't light it was the control valve at fault. After shutting off the gas, I changed the valve by removing the wires, undoing the tubing, then unscrewing the unit from the back of the unit. This worked one time. It turns out that if there isn't enough voltage from the burner, the valve won't open. I found this out after I mistakenly thought that the new valve was faulty. Check the voltage from the burner before you do anything else.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aloha from Monterey, LA
- Parts Used:
- WB28K145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacement cook-top, had natural gas orifices, needed propane
Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Golden Valley, ND
- Parts Used:
- WB02K10158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drawer support broke.
Removed the screw from the broken piece and put the new piece on and put the screw on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Villa Park, IL
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
stove top burner ignition spark progressively got weaker and then stopped on all but one burner.
I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hayden, ID
- Parts Used:
- WB16K10035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
igniter was bad and tube wasblown
repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ARDMORE, PA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hole burned through deflector oven and metal dropped onto igniter and burned it out
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Falls Church, VA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old blackened oven racks
Replaced old with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chadd from philadelphia, PA
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
2 burners wouldnt spark
Took top off, removed wires from old spark module and put them on new one. Very easy and quick, works very well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from Rochester, PA
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven would glow but the burner would not come on
My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laughlin, NV
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the old ones out and slid the new ones in. done
Was this instruction helpful to you?
Thank you for voting!