79095669104 Kenmore Range - Instructions

Pulled out the bottom drawer of the stove. Attached the new drawer glide to the drawer. Replaced the drawer and it worked like new!

I received the part two days after I had ordered it. I was very pleased with the speed of the service and the ease with which I found the part I needed on the web site. I will use your site again if needed.

Took the new parts out of the bags, slipped them into place and had the drawer working flawlessly in less than 5 minutes!
I surprised myself.

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

Part of one of the glides was still inside the hole so had to use a screwdriver to push it on out and simply put the new glides in both rear holes "very easily". Sure am glad I found this site on line. If anything else goes wrong, I will surely contact this site. Thanks. The speedy service was wonderful too. Got it in two days! Carol A. Lawless

Snapped in the plastic piece after I actually ordered the right piece....wasn't paying enough attention when ordering and didn't have a book that showed the image so I could make sure....went off the image on your website......which is awesome. Totally my fault. Thank you for your wonderful service.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

the rear glides were missing on the back of the drawer so the drawer would pull out but when pulled back in, would tip down and not catch on anything. I ordered the parts then found an instructional youtube and watched it. Easy repair, cheap!

Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey

Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on Partselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.

The drawer dropped down and would not easily open or shut or fit up good when closed. A quick inspection showed that one of the rear drawer guides was broken. The parts were ordered on a weekend and they showed up on Tuesday. We already had the pots and pans out of the drawer. It took about 10 minutes to put in the new guides (I replaced the one not broken also), clean and lubricate the drawer slides. Good as new. The repair video, although not necessary for this repair, was excellent. Thanks a bunch!

I unscrewed the two screws at the bottom of the oven door to remove door,placed on a flat surface I removed the two screws located by the handle.The oven separates into two or three pieces.I cleaned the exterior lip where the glass goes with a putty knife to remove any debris.I placed the aluminum foil,(which comes with the new window)two squares in lower corners and strips up both sides.I re-screwed everything together and all done...P.S. do not order the aluminum foil,it comes with the new glass.