91192551991 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from Granville, NY
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Plastic Roller on hinge broke in half
Following the repair video made the job very easy and quick, about a 5 minute repair. Wife says oven door never worked better. Thanks a lot for all your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from The Villages, FL
- Parts Used:
- WB57T10110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced Oven Door Exterior Glass Panel
Removed 4 screws from the panel that attaches the glass to the door along with 2 screws that attach the handle replaced the glass reattached the handle and door panel, all within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Baker from Durant, OK
- Parts Used:
- WB15K5076
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The door handle on the over was broken.
I removed the oven door from the range. Removed the broken handle and replaced the new one.
Was this instruction helpful to you?
Thank you for voting!
Stove door handle broken
Unscrewed the old broken pieces to the handle and put on the new handle, very easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wiscasset, ME
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Door handle end cap got brittle and broke on oven door.
Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lelia from Vienna, VA
- Parts Used:
- WB17X210
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner was unreliable...would stop working...I had already replaced the burner
I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder strip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carl from orange, CT
- Parts Used:
- WB23K5027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
large burner would not reduce heat when turned down
unplug stove, unscrew two screws on front of rangetop holding element controlls pry off controll handle and unscrew element controll, swing top up and off hinge.one at a time with needle nose plyers pull off wires and connect on new element controll.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Kingston, NY
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
left end cap for oven door
First, the order was shipped and delivered immediately. The model number had a wider range to select from and I had to guess which was the better fit. Other then that the new handle installation was a snap. Thank you and we would surely order from your company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Tallmadge, OH
- Parts Used:
- WB14X103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
hinge roller was worn out
Very,very easy. Just like the video described. Removed three screws. Released the spring and removed the old hinge from the slot. Slipped the new hinge in the slot,replaced the screws and reattached the spring. Job done! Great service!
Was this instruction helpful to you?
Thank you for voting!
Oven door wouldn't open/close properly; hinges offset & wheels broken
Followed YouTube video from PartsSelect. It was real easy to do and that video was helpful. Took off door by sliding it up off hinges, disconnected springs, unscrewed hinges & slid them out - reversed to install. Worked perfect, parts were exactly right and parts came within 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from bristol, CT
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Door would not open all the way
Well after fighting with the door for a month, i went on this site and using their information, i found the model number (in the process i found the receipt for the oven and found out it was 20 years old still looks and works like new. Pulled the door up and off the hinges, removed the drawer, saw the spring was in the middle hole, removed three screws pulled out old hinge. Installed new hinge, 3 screws and the spring. put the door back on and wow it worked! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Denhim Springs, LA
- Parts Used:
- WB14X103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hinge on oven door had a broken pulley.
Very easy job. Removed the 3 screws from the oven body, and slid the hinge out of the door. Slid in the new hinge, replaced the screws, and it was done. Very easy, wish I had done it sooner. Finding the part was easy, using the parts diagram. Rep was nice and confirmed the right part. Shipping was fast, and price was reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Glen Island, VA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace end caps
The video was very helpful.Very easey repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Richmond, VA
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken roller in hinge
Slipped off the front door. Removed 3 screws & spring. Replaced with new part. Hooked the spring & secured with the three screws.
Was this instruction helpful to you?
Thank you for voting!
Oven door hinge wheels were worn out and grinding.
Followed the online video. Unhooked the springs, removed the 3-screws on each side. Installed the new hinges in reverse order. Used the wear marks on the old springs to ID and place the new springs in the holes on the new hinges. Great company to deal with....never a surprise, Great communications letting you know that your parts were on order and then again that they were shipped with shipping info and numbers to call with any questions. The best part has been that the parts drop right in everytime I have ordered from them!!!! Thanks Dan!
Was this instruction helpful to you?
Thank you for voting!