9117318513 Kenmore Range - Instructions

Turn off electric supplying appliance,then remove oven bottom plate.Remove ignitor wires from controller and oven control,then remove two screws holding burner ,lift burner from gas valve,remove two screws holding ignitor.Replace with new,and re-assemble.

There are other descriptions here, but here's my story. I pulled the oven door off (pull straight up on it, it will come off) and removed the bottom warming drawer (there are plastic tabs on the outside of each side of the drawer--slide them and pull, several times on each side). I turned off the gas from behind the stove and unplugged the range, undid two screws at the back of the oven floor and lifted it forward and up. The burner is visible, but here is the hard part. The bolts holding the ignitor are underneath it and angled such that it is almost impossible to get any type of tool near them. I have small hands, and that helped. The screws are a bolt-head type or hex head, and I found that a one quarter inch open end wrench sort of fit. 6mm was too small and 7mm was too large. I managed to get the screws loosened after much struggling and manuvering, with half my body inside the oven, and once it was out, I was able to reach in from where the warming drawer was and unscrew the two wire leads attached from the ignitor to the power. They are held by plastic screwcaps. The reverse process was self explanatory, except that you should put the new ignitor in the oven and feed the wires down through the back panel, then attach the screwcaps to join the wires to the leads. Then go back in the oven and attach the ignitor, back screw first, and tighten it all the way, since you may not be able to reach it once the front screw is in. Also, use the screws that come with the new ignitor, since they are easier to start than the old ones. Tighten the screws as tight as you can get them so the ignitor doesn't wiggle, then turn the gas back on and plug it in, and test it before you put it back to gether. Mine worked, but it was a pain to do, kind of like working on an old car that wasn't designed to be fixed easily. Good luck.

Using the crescent wrench, I first removed the bolt holding the cover plate that separates the wiring from the broiler section of the oven.

Then I removed the wire nuts that connected the wires from the igniter to the wires from the oven.

Then I removed the two screws that attached the igniter to the oven.

I then reversed the process, first attaching the igniter to the oven, then connecting the wires from the igniter to those from the oven using the wire nuts. Finally, I replaced the cover plate on the assembly.

The primary difficulty with the process was the small space to work in. One has to reach to the back of the broiler area to remove the bolt, screws and wire nuts. Some of these operations require two hands, and there's no room for both arms in this area.

However, that said, this is the third time we've replaced the igniter. It seems that it only lasts about 4 years before it needs to be replaced. It's not all that hard to do.

Take bottom drawer out, take two 1\4 inch drive screws out from back bottom of inside of oven. Take out protector plate . Remove 1\4 inch drive screws from bottom burner[back of oven] where drawer was. Extract burner. Rest is self explanitory. Good luck. . . . . .

I removed the bottom cover inside the oven. Beneath that was another cover held by two screws. I removed these and the ignitor was right there. I removed the bracket screws and pulled the ignitor away from the back wall of the oven and cut the two wires close to the ignitor, leaving enough wire to reconnect the wires from the oven outlet to the new ignitor with the supplied wire nuts. Then I re-attached the bracket to the new ignitor and once that was done simply reattached the unit to the back wall of the oven. The whole job is pretty straight forward, the only difficult part being the limited work space INSIDE the oven.

took the bottom plates off with philips screwdriver.(note) there are two plates..outter and inner..to get to the two screws on the igniter.Remove igniter(two nuts). Install new. Cut the wires from old(lower part of oven and rewire with porclain wire nuts.Very simple...Partselect was great too..very fast shipping. Will do buisness again.

I removed the oven door, racks, and oven floor. That was easy, the floor had two thumb screws and one phillips/hex screw. I removed the lower drawer and the 2 covers above the drawer. The igniter was held in place by two phillips/hex screws. Had to manuver a bit to get the right angle to remove the screws. THE MOST IMPORTANT PART OF THE REPAIR, when you cut the two wires to remove the old igniter, cut them off as close to the old igniter module as possible. On my stove one of the wires on the new igniter was about an inch too short and I had to add a section of wire. Overall the whole job was easy. Keep track of screws as you remove them.

I first read and printed out several postings on how others did the job. I read and re-read them and then I started. I cut power to stove and left gas on. I removed door, pushed back and removed bottom burner cover. I exposed the igniter which I deduced was the problem. I removed the front burner screw and the rear screws (2) and the burner came out very easy. I removed the igniter from the burner, made sure which wire went where (I marked them)an snipped them. I used the ceramic caps and spliced the wires. I replaced the burner and turned on the power. I turned the oven knob on and "Viola", the igniter came on and burner came to life. I replaced every thing in reverse order and called it "done". It was so easy with the postings on this subject.

Removed the bottom cover plate and the bottom storage drawer. Disconnected the burner and removed it. Replaced the old igniter with the new one. The new one required the wire connectors from the old one to be spliced onto it. Reattached the ignitor to the burner and reinstalled the burner. Tested the new ignitor before reinstalling the cover plate and storage drawer.

The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

I removed the oven burner while the igniter attached. put unit on my bench and changed the igniter and reinstalled the burner and reattached the wires to the supply terminals. Tested the unit and it lite up ok.

frist tested ignitor with meter removed ignitor order
part , I recieved to my surprise next day I'm a very happy person

The biggest problem is to get down low enough and far enough back to be able to reach the igniter. Other tan that , it was a simple affair.Unscrew the old one and detach the wire nuts and reverse the procedure for the installation and hope the gas valve has'nt been affected