91193401992 Kenmore Range - Instructions

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Removed the old burner bowls, replacing them with the new ones.

I removed the two screws that hold the element, then I took the back cover of the range to have access to the wires, after that, I took the old one out, placed the new one and finally hooked the wires and placed the two screws right back. Very easy. I thought about bringing someone to do the job, and after I was done, I couldn't believe how easy it was.

Pulled the range out from wall (which took most on the repair time to do), removed back cover, pulled of terminals, went inside oven a remove the two screws holding Bake element. Inserted new element, tighten down screws, etc.............

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.

Took the old racks out andcslipped the new ones in

Ordered the part, it arrived and 5 minutes later it a complete installation

Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes

Just removed the old racks..and replaced them with the new racks...That's all...

pull out, push in

I'm so pleased with the ease of placing my order, the price, and the speed of delivery. My only challenge was figuring out the correct part to order, as I didn't have an owner's manual for the range when we moved into the house. But once I located the model # in the range's lower drawer, the website did a good job of guiding me toward the correct replacement part. In my case there was no "repair" involved; I was simply replacing a broken lower oven rack. I would definitely use this company again.

turn off power to the stove
Pull the stove away from the wall
remove center (metal) wire cover (5/16 nut driver needed)
disconnect 2 quick connect clips
back to the front of stove, open oven door
using 5/16 nut driver, remove 2 screws
pull out old element
insert new element
using 5/16 nut driver, reinstall 2 screws
go back to the rear of stove
reconnect 2 quick connect clips
reinstall center (metal) wire cover (5/16 nut driver needed)
turn power back on
ready to cook

Being that the rest of the stove was functioning fine, it was still plugged into the electrical outlet, after unplugging the range, I used a nutdriver and and removed the back panel exposing the two electrical clips on the old heating element. After unplugging the two electrical clips, I removed the two screws that secure the heating element to the back of the inside of the range. Once the screws were removed, the heating element came right out. I inserted the new element, installed the two screws previously removed, plugged the two electrical clips on the back of the heating element, re installed the back panel, plugged the range in and cooked lasagna. Total repair time was 12 minutes.