79092413203 Kenmore Range - Instructions

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Pulled out the bottom drawer of the stove. Attached the new drawer glide to the drawer. Replaced the drawer and it worked like new!

I received the part two days after I had ordered it. I was very pleased with the speed of the service and the ease with which I found the part I needed on the web site. I will use your site again if needed.

Simply secured new glide into slot. I was more impressed at how easy this company made it for me to find the part I needed. And, they shipped immediately. This company is great.

I watched the video before ordering the part. When it arrived, I knew exactly what to do. No tools were needed. It took me 2 tries to get the drawer aligned properly but the whole repair took about a minute. The video was invaluable!

Snapped in the plastic piece after I actually ordered the right piece....wasn't paying enough attention when ordering and didn't have a book that showed the image so I could make sure....went off the image on your website......which is awesome. Totally my fault. Thank you for your wonderful service.

Part of one of the glides was still inside the hole so had to use a screwdriver to push it on out and simply put the new glides in both rear holes "very easily". Sure am glad I found this site on line. If anything else goes wrong, I will surely contact this site. Thanks. The speedy service was wonderful too. Got it in two days! Carol A. Lawless

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

I am an electrician so I had no problem identifying wire and connecting them properly. However there were no instructions provided with the part and the configuration of the new switch was different than the the old one. I doubt if a DIY individual would have been capable of handling this task. Also there were no safety warning with respect to electrical repairs, which is a must today.

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,

Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

Unplugged the main cord to the socket in behind range. Took back panel off. Unscrewed switch from its position on face of range. Switch is not a look alike switch to original, so had to pay attention to the labeling on both switches as to their identity. Removed one line at a time from old switch and placed on new switch. Rechecked positions of the wires and made sure there was no binding of the wire positions when installed. Mounted switch to same position previous switch was removed. Reinstalled back panel, plugged in range and tested switch. Very easy repair as long as you can see the labeling on back of switches. I used a light having a strap that is positioned on my head for best lighting possible for one person repair.

Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.