79079914300 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- charles from cartersville, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element burned up
removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WESTMINSTER, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
No oven heat, but the broiler worked fine. All top burners worked.
Removed the oven heater and checked with an ohm meter. It read 'open', so I ordered a new element. It came in a few days, and my 16 year old grandson installed it, and all is well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from JACKSON, MS
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned element !
replaced the element !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ALBANY, OR
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Burned out bottom oven element
Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from SAINT PAUL, NE
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out in the house we rent
Easy as removing 2 screws, pulling the wires through the back wall of the oven so I could connect the new element and replacing everything. Honestly, it only took around 8 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from ROCKVILLE, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken element
Simple installation took 2 minutes to do...pop on the connectors, screw each end into back of oven...DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from LAUREL, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burned through in one spot; oven would not heat
replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from NEWPORT, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
It burned out. Broke to peaces
I watched a YouTube video. Than it was easy. I turned the breaker to range off. Took the nuts off. Uncliped the part. Plug new part in. Put screws back in. Flipped on the breaker. And it works wonderfull.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donise from WILLINGBORO, NJ
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element had burned out.
I followed the instruction on the web site and the installation was just like the instruction. Very quick and easy. I was so happy and now I am baking up a storm again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from CASTALIA, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Stove Element Stopped Working
Unpluged Oven, Removed 2 screws, unpluged Element, Plugged in new element. Replaced 2 screws, plugged oven in. Done 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from STRAWN, TX
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven not heating properly.
Viewed the video and simply removed the two screws with a 1/4" nut driver, removed the existing bake element and installed the new one. Quick and easy, even for someone who is not mechanically inclined.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from MARIETTA, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element in oven burned through
Turned off circuit breaker to the oven, unscrew the 2 small screws, pulled the element away from the back, pull element away from the wires in the oven and replace with the new one and replace the screws. Tirn circuit breaker back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from GERMANTOWN, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element broken
Removed old element with a nut driver, 2 screws. Disconnected electric wires on element, being careful not to let the wires slip into the back of the oven. Connected the wires on new element, lined up holes with holes on oven and screwed in 2 screws with nut driver. Done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from KLAMATH FALLS, OR
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burnt in half
All that was needed was to unscrew two screws holding it to the back of the oven and pull it out to get to the wires. Then unhook the wires and install new one. Less than 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JONESBOROUGH, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burn into
Remove the old one and replaced the new one. It was very simple, fast, and easy.
Was this instruction helpful to you?
Thank you for voting!