66572014104 Kenmore Range - Instructions

Replaced both rollers....Quick and Easy!!

This repair is only if your old igniters are working but they are so cracked that the spark is not going where it should be. TURN OF THE GAS SUPPLY VALVE BEHIND THE STOVE AND UNPLUG THE STOVE FROM THE WALL.I had to drill out most of the old screws to remove the burners plates because of all the old baked on spills. I bought replacement screws when I bought the igniters because I felt this would be a problem. My repair time included scrubbing the stove top. Once all the parts that make up the stovetop burners were removed (NOTE WHICH BURNER PLATE CAME FROM WHICH LOCATION, THEY ARE DIFFERENT SIZES) and I could see the pipes beneath the stove top, I cleared off the top and used a spreading knife to push in the clips on the left and right sides near the front of the stove. It was thin enough to fit in the space between the stove top and main body. Push the clip inward and pull up on the stove top and it will let you lift the top. Be careful because it may release suddenly so be gentle. I also removed the top section of the back of the stove to access the igniter terminal block. A few screws, nothing more. Be sure to take note of which wire goes where. (They are color coded). Unplug the old igniters. it is easiest to cut he old igniters off of the end of the wires and pull out three wires leaving only one. At the back left of the top of the stove there is a rectangle channel that the wires are running through. There is a clip that holds the wires loosely together. Remove the wires from that clip or the next part will be difficult. Run each of the new igniter wires through their respective holes in the stove top. BE CAREFUL NOT TO DAMAGE THE WIRE INSULATION IN ANY WAY. When you put the burner plates back on the igniters will be sandwiched in between the plate and the stove top. Using electrical tape, tape the connector ends of the new wires to the one remaining old wire. Gently pull the old wire through the rectangle channel, pulling from the back of the stove. Take your time so no damage occurs. Once the wires are pulled, plug them in to their respective terminals and place the wires in the loose clip. Make sure the new wires are not crossing the pipe openings where the burners are located. You can close the stove top and double check there are no wires across any of the burner openings. Re-assemble the burners and plug in the stove. DO NOT OPEN THE GAS VALVE. Turn on the stove and check to make sure the new igniters are working properly and sparking to the burner plate assemblies. You should see a controlled spark. Do not touch the burner plates or igniters or you will be shocked. If all are working then you may put the back cover on and open the gas valve. If none are working make sure the stove is plugged in. If some are working then check the connection on the terminal block and the wire insulation. If they are still not working then you've got bigger fish to fry. Good luck my friend. Happy fixing!

I used the allen wrenches to block the hinges, removed the oven door and used the kitchen counter for a work station. I removed the trim piece at the bottom which released the side trim and oven glass front, and then reversed the procedure. It took more time to clean things than to do the exchange. My only issue is with Fed Ex who delived the first trim piece bent in the middle inside a crushed box. Part Select had another part sent the same day after I called them.

The replacement proceeds similarly as for electric range switch replacements described here, only this model is a gas range. The top panel does not lift up because of the feeds to the gas burners. It is possible, using a thin blade, to depress the spring fingers holding the switch in the oven panel, or else to remove it destructively. Be careful not to pull the old switch out too far, or else the wires will pull off the switch connectors and fall inside the oven-side panel cavity. This happened to me. The wires are very short. Another 1/2 inch of wire would have made all the difference. If this happens you have to fish out the loose wire. I gave up on this and took off the back panel (about 8 screws) and then loosened the bottom and sides of the side panel. This allowed me to retrieve the short wire and connect it to the back of the switch while pushing the switch into its mounting hole. Reattach the side panel, the back panel, and slide the stove back into place, and you should be good to go.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

Remove oven racks. Remove bottom of oven. Mine was held in place by two large screws in the back part of the oven. They did not screw into anything. Lift out bottom from the rear. Remove burner cover plate by lifting the front and pulling out. Mine was not screwed in. The igniter is mounted on the burner and held by two 5/16 small bolts. The top one is easily accessible. The bottom is a real witch. You need 1/4inch socket set with universal connector to remove. There is a single wire attached to igniter by a wire clip. The wire is accessible by removing the bottom pan storage drawer under the oven door. Unclip the old attach the new. Screw two small bolts back in and replace things you took out. TURN GAS AND ELECTRICITY OFF BEFORE YOU BEGIN. Parts select should allow the igniter to be sold separately rather than connected to the burner. I only replaced the igniter. Replacing the burner would be a real chore.

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

First remove the oven racks and the burner cover in the bottom of the oven. There are two phillips screws near the back. Loosen the screws but it is not necessary to completely remove them. Pull out the bottom cover and this will expose the burner. There is one phillips screw at the front of the oven and one at the back. Remove these screws and set aside. You should be able to remove the burner and unplug the wire connected to it. Replace with a new burner in the reverse order. Plug in the wire and make sure the new burner is seated properly over the gas valve. It lines up pretty easily. Put the rear screw back in but be careful not to drop it into the hole otherwise you will have to use a magnet to retrieve it or pull the oven out because it will be on the floor. Replace the front screw and put everything else back together. Pretty easy job

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.