9116483190 Kenmore Range - Instructions

I took out the two racks from inside the oven. I then took my cordless screw driver and unscrewed the two hex bolts from the back of the oven , where the element goes through the other side. Next I went to the back of the outside of the oven and unscrewed the two hex bolts that hold the gray guard on(It covers the wires). I unplugged the red and the yellow (might have been a white wire since it was dark back there). wires that connect to the element. I went to the front of the stove and took out the bad element. I took the new one and inserted it into the two holes from the old element. Plugged the red and yellow wires back up and replaced the guard. Lastly I screwed the element to the rear of the oven with the two hex bolts I used before.

first removed the two screws,pulled the element out ,disconnected the wires, pulled it out , cleaned the oven and then reversed the process. could not have been easier for a do it yourself homeowner on a budget.

The replacement element came within a couple of days of our order. From the time I saw it by the front door till the repair was complete was about 10 minutes. Half the time was taken in walking to my tool box. In just a few minutes we had tested the new element and were ready to make dinner. Great value for the price.

First I unplugged the stove. I then removed the two screws that held the element in place. I then pulled the element out about four inches to expose the connection. I disconnected the two wires, removed the element and replaced it with the new one. I then reassembled the oven in reverse order. It was very simple.

removed two bolts on the inside of the oven, disconnected the two electrical connections in back which were a little set so I had to use pliers and removed old element. Reversed procedure to install new element.

The >15 minutes includes vacuuming out the oven.

partselect.com deliver was extremely fast and the part was packed securely. We would order from them again without a problem.

Turned off circuit breaker, removed the two screws, pulled out the wires, unhooked the connections and hooked up the new element. Put the two screws back in, turned on the power and it worked! So, so easy! I wouldn't have attempted it had it not been for the other stories associated with the part I purchased.

replace coil 2 clips off 2 clips on........

I removed the 2 screwws inside the oven cavity and pulled the element towards me. I unplugged the wires from the element and plugged in the new one and secured it in place with the 2 screws.

Shut off electrical supply to stove.Remove 2 screws.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.

Turned off the breaker to the stove, removed oven racks, used small pair of plyers to remove bolts (2) holding defective element in place. Pulled (2) wires that had a snap connection apart. Old element was not removed. Connected (2) snap wires, pushed them back into the oven wall, used plyers to re-connect the element to oven. Installation DONE!
Turned on breaker and then the oven; we are now baking again.

It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install

After noticing it needed replaced I went to PartSelect, put in model/serial# and order that easy. It was here the next day. The oven was fixed. Now back to baking...thanks PartSelect.

Very well, I made a mistake with the model #. So I had to return and reorder .

I really like my repairman, but prefer to do it myself. PartSelect rocks...reasonable prices, really fast shipping AND online repair videos keep me coming back. The repair was exactly as the video described, but one of the wires came loose as I was pulling the element through. I thought I'd have to tear the stove apart to get to it, but luckily, all of the wiring is contained in a raceway that runs along the back of the stove. After removing it to expose the wires, I would recommend doing so instead of trying to pull the wires through as the video shows. In doing so, the terminal connections are readily accessible and it's much easier to remove and install the bake element without having to worry about feeding the wires through at the same time and running the risk of damaging them. Overall, a very simple, quick repair that saved me a $50-75 service call.

I followed the directions in the video on the website. The repair was so easy!! I simply unscrewed the screws holding the element in place at the back of the oven, pulled the wires out. This did take a little bit of time, as I didn't want to pull the wire off of the element and lose it in the back of the oven, but I was able to eventually work it free from the insulation and make the connectors visible. I slid off the old element, slid the wires back on to the new one and pushed them back into the wall of the oven and replaced the screws. Works like a charm!! I will definitely use your website for other appliance repairs!!