9117398612 Kenmore Range - Instructions

I had to replace the ignitor. The wiring was simple. Just had to connect two wires. The difficult part was removing and replacing the ignitor. It is suspended by 2 screws that are very difficult to access.

The repair was easy and not very time consuming. It didn't take very long to fix the problem and thanks to this site, I was able to save the money I would have spent if a repair technician came out to do the same work. Now I can afford Christmas and cook too!

First had to disconnect the old igniter by removing screw with a small wratchet wrench. Then pull out approximately 3" of wire from the old igniter, cut off old igniter, attache replacement igniter with supplied wire nuts, shove excess wire back into wiring compartment and then attach the new igniter.

I removed lower drawer, removed oven door,
took out rear screws to oven pan,removed screws that attatch ignighter to oven wall,disconnected wiring and removed old ignighter. reversed process to install new part. total repair time was about 20 minutes. Also take into consideration that i am a building contractor familiar to appliance repair etc.

I removed the igniter by first removing the oven racks then the oven pan and oven catch pans. I open the lower draw to the oven and removed the drawer. I reached back under the oven and clipped the wires that run to the igniter and striped a half inch of plastic to expose the wire. I removed the igniter from the burner and replaced with new igniter. I then fed the wires back through the hole the cut wires came out of and used the wire nuts supplied to connect. Replaced other parts in reverse order and tested. Works great.

frist tested ignitor with meter removed ignitor order
part , I recieved to my surprise next day I'm a very happy person

The biggest problem is to get down low enough and far enough back to be able to reach the igniter. Other tan that , it was a simple affair.Unscrew the old one and detach the wire nuts and reverse the procedure for the installation and hope the gas valve has'nt been affected

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.

Take bottom drawer out, take two 1\4 inch drive screws out from back bottom of inside of oven. Take out protector plate . Remove 1\4 inch drive screws from bottom burner[back of oven] where drawer was. Extract burner. Rest is self explanitory. Good luck. . . . . .

First I removed the bottom oven drawer then
I removed the heat shields. I removed the two
wires that connected the igniter and the two screws holding the igniter and removed it. I
replaced a wire connector on one side of the
igniter. The other igniter wire I soldered together
to the other wire. Then I replaced the igniter by
reconnecting the two mounting screws. Then I replaced the heat shields and the oven drawer.

I followed the advice in the previous repair stories as this was very helpful.

I didn't know if polarity on the igniter mattered, so to be safe I marked the same wire on the old igniter and the corresponding wire on the new ignitor and plug, so it would be hooked up with the same polarity.

I took the burner element out to make it easier to replace the ignitor. I made sure to leave plenty of wire when cutting the connectors off the old igniter. Hooked everything up and it worked perfectly.

well,as with any repair that looks easy,i had to do a little more than what i had originally anticpated.
i was hoping for an access panel to the igniter,but after removing the lower drawer,there was only the heat shields and pans,about 20 screws later i got
to the igniter and spliced it in place,then reassembled it without too much fuss -now my 93 year old friend can bake her pecan pies for charity that is her favorite hobby-thanks

Using the crescent wrench, I first removed the bolt holding the cover plate that separates the wiring from the broiler section of the oven.

Then I removed the wire nuts that connected the wires from the igniter to the wires from the oven.

Then I removed the two screws that attached the igniter to the oven.

I then reversed the process, first attaching the igniter to the oven, then connecting the wires from the igniter to those from the oven using the wire nuts. Finally, I replaced the cover plate on the assembly.

The primary difficulty with the process was the small space to work in. One has to reach to the back of the broiler area to remove the bolt, screws and wire nuts. Some of these operations require two hands, and there's no room for both arms in this area.

However, that said, this is the third time we've replaced the igniter. It seems that it only lasts about 4 years before it needs to be replaced. It's not all that hard to do.

Removed oven bottom panel. Removed lower drawer to access old igniter. Had to take a cover panel off to expose igniter. Unscrew two screws to remove igniter which was a bit awkward to reach. Then simply put new one in its place.