79090102207 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lorraine from NORTH MANKATO, MN
- Parts Used:
- 318255001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element had broken in half in our 24” Tappan range.
We removed the backplate from our range unhooked the element Lug connection .Then we unscrewed the 2 screws in the oven holding the old element removing it screwing the new element into the oven wall. We then hooked the rear connections to the lugs and replaced the back plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Portland, OR
- Parts Used:
- 318394803
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not recognize the door wasn't shut
I was required to remove the control panel to access the plug as it had been broken and the switch had been shoved into the unit . It would have been extremely simple if the plug had remained on the outside surface
My son can now clean his dirty oven
My son can now clean his dirty oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from CHESTERTOWN, NY
- Parts Used:
- 318255605
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
top electric burner not working
2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
Drip bowels needed to be replaced
I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from HAYDEN, AL
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cooktop burner was wore out from age
Just pulled the old cook top burner out and put the new one in .it took about 1 1/2 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from GREELEY, CO
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heating element burned out
All you do it unplug the old one and plug in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conan from Moline, IL
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Two burners did not heat
Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from EDGAR, WI
- Parts Used:
- 5304504897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
sensor should pull into oven enough to easily unsnap and snap but didn't pull out
on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from WEATOGUE, CT
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original Element physically broke
There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony J from HAMMONTON, NJ
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the burner stop working
Just followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Spencer, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" stove top element would not warm up.
It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!