79060721903 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clarence from Bronx, NY
- Parts Used:
- 5304506426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One burner had broken
I put in the part and it went well, I have used other parts from your factory for the same stove so I knew it was going to go easy. The part only required one screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joy from ANDERSON, IN
- Parts Used:
- 316032411
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would come on when turned off
It was so easy. I am 66 yrs old. It only took 30 minutes and a screwdiver. I was totally amazed and I thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRADLEY from SHERIDAN, MI
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven wouldn't light consistently
remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from VIRGINIA BCH, VA
- Parts Used:
- 5304509706
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Low amperage to gas safety valve no gas flow.
Disassembled inside of oven. Slid away from wall opened back replaced safety valve and igniter. Safety valve was good changed only because it was apart. Resemble and test sat. Kept old safety valve for emergency spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vajai from RICHMOND HILL, NY
- Parts Used:
- 5304509706
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Igniter gets hot but wouldn't ignite
I did the repair with the instructions from parts select
It was very self explationatry
Thank you parts select
I saved at least $400.
It was very self explationatry
Thank you parts select
I saved at least $400.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Roanoke, VA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lacking oven racks on used appliance
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Darragh, PA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an additional rack
Open the door and slide in the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from YAMHILL, OR
- Parts Used:
- 316243723
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Wood Burning Oven
The Appliance light was installed in a wood burning oven used by a commercial bakery. The entirely masonry oven is used to cook a specialty product with origins in Brazil.
We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodate the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced.
The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.
We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodate the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced.
The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Wappapello, MO
- Parts Used:
- 316243723
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Had to go from nat gas to lp
Replaced uper orifice n adjusted oven as instructed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blanca from Union City, NJ
- Parts Used:
- 5304534377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced theoriginal power cord.
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pekin, IL
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would Not lite
Watched a half dozen You Tube Videos before I saw the Exact one-Submitted by a Woman-Super Easy-Had the Exact Part from this site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from WEST ROXBURY, MA
- Parts Used:
- 5304509706
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Gas oven stopped working. I read that it probably was the igniter. Bought a new one to ins
YouTube video I used was for a newer version of the same model stove. Door did not have latches to remove it. It was fairly easy getting to the old igniter but a bit of a struggle getting to unplug it, as the connector was behind a small metal shield in the bottom left corner of the oven. Because I couldn’t remove the oven door, it made it more difficult to undo the screw holding it in. I finally did, and from that point it went smoothly. I was worried that I was going to access it from the back, but I didn’t need to. I installed the new one, turned gas back on, moved the stove back to position, and turned on the oven. Very happy to have succeeded, adding a few more years to the stove and saving money for the installation of the igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Fort Wayne, IN
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old oven racks were nasty!
We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Cincinnati, OH
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed an extra oven rack to bake more at one time.
I just installed the extra rack and re-arranged the existing ones. Works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. Steven from Morristown, NJ
- Parts Used:
- 5304506427
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner hard to ignite, ports probably clogged
Simply lifted out the old burner assembly (no tools needed) and drop in the new replacement.
Was this instruction helpful to you?
Thank you for voting!