79094153310 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- greg from SANDY, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
burner switch failure
Unplugged the range. Removed the top section of the back of the stove to expose switches. Removed the knob, (pulls off exposing the 2 switch screws), unscrew & pull out from the back. The new switch was slightly bigger but the same manufacture and post letters & numbers. Transfer wires one-at-a-time from the old to the new switch. Mount the new switch back in place, put the screws in and the knob on. I plugged in the stove for a quick test, HA....works perfectly. Unplugged again and put the back panel back on, plugged back in and pushed the stove back in it's hole. BEFORE; the old switch when turned down would come back on BUT stay on high, a lot of boil overs. FINALLY: when turned on, it would NOT turn off, a real fire hazard. Thank you for having an original replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sajeed from GRANADA HILLS, CA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The burner on the top left (closest to front) would not turn off.
1 - Turn off the power from the panel. 2 - Unplugged the range from outlet. 3 - Unscrewed the black hex screws from the rear panel. 4 - Took a pic of the bad infinite burner switch to ensure the correct wires would connect to the new switch. 5 - Removed knob and unscrewed switch, then replaced with new switch. Matched all of the wires to like, L1, L2, P, H1 and H2. If any wires do not exist for your switch, it is ok because not all ranges use all wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from ASTORIA, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Electric element would intermitantly go on high, even on low settings.
Slid stove out, disconnect power plug, removed top control panel with 4 screws. Unplugged two electrical connectors. removed knob and nut removing switch. Re-assembled in reverse order and test all functions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Florence, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burner was inconsistent the heating with red hot one minute and not the next minute
I watched the video on how to do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from LAKELAND, FL
- Parts Used:
- 316400601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom oven pan was warped and discolored
Unscrew the 2 screws at the back of the oven bottom pan in the range. Place new oven pan in and rescrew the 2 screws. I could not get the two screws screwed back in. Since the bottom pan cannot move from its position, I felt like the two screws were not necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Elizabeth City, NC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged
snap out the old one and snap in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MOUNT VERNON, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners constantly overheating, and inconsistent heating.
With the stove pulled out and unplugged, There are 4 square head screws to pull a metal plate off the back of the range. Once that is off, the infinite switches are in line and can be removed with a philips head screw driver/bit. I placed each wire onto the new switch as I removed them from the old, to avoid any confusion. The entire repair took less than 10 minutes. Incredibly easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Edina, MN
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large front burner would not come on under setting of "3"
Replaced infinite control very easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from New Castle, PA
- Parts Used:
- 318372211
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner element failed
Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adolfo from new york, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element gets very even the control is at minimum
Removed the defective part. Install the new part, insert the connectors. Now its working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Storm Lake, IA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dead burner
I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from North Mankato, MN
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Arcing could be heard (and later seen) inside the switch
Switch was easy to replace. Some hex head screws to remove the panel and two screws to remove the switch. Though the plug in positions were totally different, all the quick connect terminals were marked on both switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deane from WINCHESTER, KY
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
temp. probe
Easy watched on line video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Batesville, AR
- Parts Used:
- 318372211
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
An aluminum saucepan had overheated and melted onto the element.
Unplugged the element and the melted on pot. Plugged in the new element. I thought I might need a whole new cooktop but a new element was very easy to find online.
Was this instruction helpful to you?
Thank you for voting!