9114688813 Kenmore Range - Instructions

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

Installed easily, was most impressed with the speed of delivery and it was the perfect size!!

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Followed the instructions from the video. The repair was really easy and quick.

Door in upright position, removed lower drawer to access spring, replaced broken spring. Less than 5 min.

I went by the video

Removed old broken element and installed new one. Took less than 10 minutes

first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.

First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..

Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.

By myself

Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven. I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.

Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.

After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!

Quick and easy, thanks!