1033247812 Kenmore Range - Instructions

i removed the oven door and then the lower panel.the two screws holding the igniter were hard to access, so i removed the gas rail.this made the job much easier. the advice from other people on this website was very helpful and made the repair much easier.just remember to shutoff both the electric and gas supply.

The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)

I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut the cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.

I removed the oven grates and removed 2 screws that held the bottom pan in the oven to get easy access to the burner and igniter. Remove 2 screws that held the burner in place. Removed wire nuts. Removing burner allowed easy access to fasteners holding ignitre in place. Confirmed that the igniter was bad by checking the continuity. Ordered part later in the evening from parts select. Part was here 2nd morning after I ordered it. Installed, and checked to make sure igniter wasworking properely. When check confirmed igniter was working, replace oven components. Saved myself $100 or more by doing it myself rather than having a repairman out.

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

I took the old igniter out and replaced it with a new one.

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

Basically followed the instructions that others had posted. Removed the bad oven igniter by removing the two screws securing it to the burner. Attached the new ignitor and then spliced the new wires into the old wires with the ceramic nuts that came with new igniter.

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)

Removed old igniter coil by removing 2 small hex head bolts and pulling the two wire plug connectors (be sure to unplug the range). Installed new coil and connected the wires with the ceramic wire nuts supplied with the new part.

Removed bottom tray of oven, removed ignighter, unplug two wires.

Took off the 2 bottom covers, saw the igniter did'nt glow, checked for voltage,yes.Ordered part. when had part,pulled out ignitor,respliced wires, and did in reverse order.