1033248291 Kenmore Range - Instructions

The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)

I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut the cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.

I removed the oven grates and removed 2 screws that held the bottom pan in the oven to get easy access to the burner and igniter. Remove 2 screws that held the burner in place. Removed wire nuts. Removing burner allowed easy access to fasteners holding ignitre in place. Confirmed that the igniter was bad by checking the continuity. Ordered part later in the evening from parts select. Part was here 2nd morning after I ordered it. Installed, and checked to make sure igniter wasworking properely. When check confirmed igniter was working, replace oven components. Saved myself $100 or more by doing it myself rather than having a repairman out.

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

Good friend said he could do it no problem at all!!!!!

1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

I took the old igniter out and replaced it with a new one.

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

I removed the bottom cover inside the oven. Beneath that was another cover held by two screws. I removed these and the ignitor was right there. I removed the bracket screws and pulled the ignitor away from the back wall of the oven and cut the two wires close to the ignitor, leaving enough wire to reconnect the wires from the oven outlet to the new ignitor with the supplied wire nuts. Then I re-attached the bracket to the new ignitor and once that was done simply reattached the unit to the back wall of the oven. The whole job is pretty straight forward, the only difficult part being the limited work space INSIDE the oven.

Per the instructions included with my part and from reading prior posts, I unplugged my range, removed my storage drawer, took the screws out of the bottom pan and removed. I found the igniter really easy to locate. As it was held in by a bracket that was soldered in, I found no need to remove many screws or to add the included mounting hardware as the part instructions suggested. I removed it, placed and mounted the new igniter (only two screws) before I snipped the connecting wires. Stripping the insulation material off of the wires seemed to be the MOST difficult part! I spliced the new to the old using ceramic caps enclosed with part, plugged in the range and fired it up...just to be sure it worked, and it did! I reversed the process to put it back together. Voila!

Removed oven bottom panel. Removed lower drawer to access old igniter. Had to take a cover panel off to expose igniter. Unscrew two screws to remove igniter which was a bit awkward to reach. Then simply put new one in its place.

To diagnos i removed the lower tray and could see the ignitor was not lighting like the broiler was,the same ignitor.I had the same problem as some of the other people so that was helpful.I removed bottom storage tray and could get to the wires and it was an easy fix,took about 40 minutes total.This website was very helpful also with excellent service on the parts and i saved a bunch of money!
Thanks,Gerald