9114618810 Kenmore Range - Instructions

1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven

The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.

Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!

removed oven door, removed drawer under oven, removed three screws holding hinge assembly, unhooked spring from hinge arm, inserted new hinge arm, attached spring, positioned hinge assembly and replaced screws, reinstalled drawer beneath oven being certain that no pot handles interfere with the hinge spring loaded arm, reinstall oven door.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)

I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!

Slid off the oven door and loosened the hinge assembly. Removed the storage drawer to unhook the spring and then took off the old hinge assembly.

Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.

We can now bake bread, pizza, etc. What a relief.

I went by the video

Removed old broken element and installed new one. Took less than 10 minutes

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

I followed the way all the others on this website did the repair. It was so easy. I turned the power off to the oven, then disconnected it from the back oven wall, pulled it out a bit, disconnected the wires, and put it back in.

Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.

THANKS SO MUCH!!!

Shut of circuit breaker. Removed two screws with socket set . pulled element out about three inches, disconnected and held wires in place with clip type closepins. pressed connections onto new element , secured screws and presto... All too simple and in less then 15 minutes.
Reading previous reviews was quite helpful

first husband removed the bolts unplugged old element wires -plugged in new element wires and but in bolts - unfortunately the oven still doesn't work not sure if element is bad or wiring, need professional help

Replacement of the heating element only takes a few minutes...First, turn off the breaker/fuse to the stove, then just remove two screws , pull out the two connected wires to expose the connections, hook them up, and replace the screws to the cover plate. The connection/cover plate can be hinged or not hinged. Make sure you order the correct one. We ordered the wrong one at first, but were assisted by the returns dept. and received the correct one in 2 days. Great customer service, thanks partsselect.com!!

I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.