9117359181 Kenmore Range - Instructions

Called in and talked to someone and he look yup what he thought was correct but after i got them theywere wrong so i sent them back for a full refund minus 9.90 freight. I still need to figure out what i need for my 27 inch wall oven. Please help. Thanks

REMOVED DOOR TO OVEN
REMOVED HINGE [3 SCREWS]
REMOVED BOTTOM DRAW
UNHOOKED SPRING FROM LEFT SIDE ATTACHED TO HINGE
PULL OUT DEFECTIVE HINGE
REPLACE WITH NEW HINGE AND SCREWS
REHOOK SPRING TO HINGE & REPLACE DOOR
COMPLETE

FOLLOW VIDEO PROVIDED BY PARTS SELECT

Lifted the door off the hinges, unhooked the spring from each hinge, unscrewed 3 Phillips head screws from the face plate of each hinge and removed the hinge assemblies . Hinges went in the way they came out; easy shmeasy. Took less than 15 minutes and the door is like new.

replaced lights in refrigirator and freezer

1. Slide oven door off hinge arms and set aside
2. Slide out oven bottom drawer and set aside
3. Detach springs from perforations in stove rails then hinges and set aside
4. Loosen three screws in each hinge, remove and set aside.
5. Remove hinges, threading them out through openings
6. Thread new hinges into stove openings. Align hinge arms with hinge wheels.
7. Align and tighten three hinge screws in each hinge.
8. Re-attach springs to perforations in hinge, then stove rails
9. Slide oven drawer into stove and door into hinge arms

Not sure how common broken springs on Kenmore ranges or any other brand are, but both springs broke on my Kenmore oven door. When both springs break the door free falls to the open position which is dangerous. Replacement part number was unavailable so I found a spring the same length and diameter on the site. I then called Parts online and asked if they thought the replacement spring would work. They were quite helpful and said they said it should work. Upon arrive of the springs I pulled the bottom drawer under the oven totally out to gain access to the broken springs. The top of the spring connects to the door hinge and the bottom connects to the oven frame. Replaced bottom drawer. Total job took about 15 minutes.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

After tilting the oven door out and sliding it up to remove it, I slid the storage drawer our completely from the range. After removing the spring that held the hinge assembly under tension, I removed 3 phillips head screws that held the existing assembly in place and removed it. After verifying the part you sent was an exact match, I reinstalled the new part, fastened the screws, attached the tension spring, installed the storage drawer, and then slid the oven door back in place on the brackets, completing the repair.

1) Verified it was the broiler igniter that was damaged.
2) Removed the oven door, the lower pot storage drawer and the top range panel.
3) Turned off the gas supply in the top range area. Pulled the electrical plug-in out of the lower electrical panel (behind the lower drawer).
4) Used the nut driver to remove the two (2) 1/4" screws that held the igniter to the back wall of the oven. I later read in the Use & Care Guide that this is easier to do if the broiler burner cover is removed first.
5) I pulled the damaged igniter away from the back wall, expecting to expose wire connectors or splicing but was only able to get about 6" of the two (2) insulated wires before I could not pull them any further.
6) Therefore, I cut the wires and, without a proper wire stripper, cut about 3/8" of insulation away in order to make a splice between the wiring from the new igniter and the wiring coming out of the back of the oven. Big mistake ..... do not recommend this without using a proper wire stripper! I must have cut into the existing exposed oven wiring on one of the wires such that when I used the twist-on to make the splice, most of the wires (those wound together to form one wire) were damaged and broke away. Unfortuantely I did not find this out until everything was put back together and we (my wife and I) did the test. No results!
7) I took everything apart again and when I tried to pull the wiring back out from in behind the oven wall, one wire came out with the twist-on in tact and the other came out "with no wire attachment".
8) I now had to figure out how to get into the back of the oven to retrieve the "lost connecting wire". It is quite simple when you know what you are doing but no instructions (that I had) advised that the upper back light gauge metal panels could be easily removed to expose the wiring. This was eventually determined and the connections were both made again in a more positive manner.
9) We (my wife and I) put it all back together and this time it was fine ..... just had to be patient while the gas purged the air out of the broiler burner line.
10) Lessons learned: GE made it easy "once you knew how it could be done". I suspect GE feels that service type people should be doing these things but with a 120VAC (vs higher voltage electric type ovens) system why not provide the info for the "do-it-yourselfers" as well?

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

I took all of the oven racks out , then the bottom cover, over the element. I immediately saw the igniter coil was broken. I took the element out and disconnected the two wires. (I saw that the igniter coil was broken and knew that must be my problem. I got my manual out and found the part number and got on line and started shopping. I found part select, the price was fair and ordered it the same day. It was shipped out to me the same day I ordered it. Received it the next day and had the oven working again. Easy to order, great customer service, fast shipping department. Great job to all of you folks at Part Select. I would recommend PS to anyone that wants to save money and do it yourself. Go for it. tk middlebury IN.

The bolts were below the base of the oven, and very difficult to remove and replace. The directions were not applicable to our unit. The good news was the igniter was correct, even though we had to adapt the bracket.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Real simple. Disengaged springs at the inside bottom, replaced hinges and reengaged springs.

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!