79046252400 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Weatherford, TX
- Parts Used:
- 903136-9020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right large burner switch only heated on "high"
I mistakenly took the two screws out of the front piece above the oven. Except for that the time would have been maybe 10 minutes. The knobs all four came off easy and so did the retainer nuts and the six screws holding the metal plate. I took the old switch out after turning off the power. I had the new switch in one hand and removed one wire at a time from the old and put it on the new one. Put the parts back in place and turned the power on and turned the switch on. Works great! Saved about one hundred and thirty dollars from what the repair service charged last time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Williamsville, VT
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace terminal block and burner unit.
Very simply following the online video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Colrain, MA
- Parts Used:
- 318328010
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
had no instructions on how to remove old door hinge recepticle..
After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from North Royalton, OH
- Parts Used:
- 903136-9020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner fluctuating erratically
In order to service the switches on this model, remove all four knobs for the switches. This will expose the plastic nuts which hold the fascia panel secure. Remove those nuts and the fascia panel. Next use a phillips screwdriver to unsecure the steel panel which secures all four burner switches. Remove the faulty switch, taking note of each color lead and terminal designation. Replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Tulsa, OK
- Parts Used:
- 903136-9020
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Infinite Switch Became Defective.
Turned off electrical breaker (double). Removed the switch handle, removed the plastic rings (special wrench) under the handles. Removed three screws up under the front of control panel. Removed six screws holding the infinite switches. Removed defective switch. Different from the new switch. Wiring locations were different on the old sw. The reason for the vom use. All is well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Glasgow, MT
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Was this instruction helpful to you?
Thank you for voting!