66575012101 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from BURNSVILLE, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Temp inaccurate
I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!
This was an easy fix for a seventy year-old like me!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from YONKERS, NY
- Parts Used:
- WPW10447925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
burner grates were very scaley(rough)
exchanged old with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PLUM CITY, WI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Clermont, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not reaching temperature
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from S MILWAUKEE, WI
- Parts Used:
- WP8053834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Impossible to do by yourself. Make sure that you have a second set of hands.
Put the bottom of the glass in first then put the top half into the brackets in the door handle. Holding it in place with your extra set of hands tighten it down with the two screws from inside the oven door into the back of the handle. The door will be open a lot so be extra careful not to let the door close onto your hands or fingers. Also remember patience is a virtue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George E from SEVIERVILLE, TN
- Parts Used:
- 8184859
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The part doesn't seem to fit the glass door
I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from CORAL SPRINGS, FL
- Parts Used:
- 8184860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
replace rusted door frame, 3 pices
The brief comments on how to with the order was most helpful, no problems replacing frame. Quality is good I thought the price was very high for the parts, considering plastic and metal pieces, but then again compared to new stove reasonable. Remove pieces replace back in order removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from OLYMPIA, WA
- Parts Used:
- WPW10447925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Peeling paint grate
Remove old grate place new grate on gas stove top
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert Ruth from FERNDALE, WA
- Parts Used:
- WP3195097
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Corroded/greasy bottom oven tray
Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from WEST JORDAN, UT
- Parts Used:
- WPW10293048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Oven would not maintain Heating
Following details from the installation video, after removing the main gas line and the two output lines I removed the four screws that removed the valve but found it was easier to remove and install the new one if I first removed the oven burner(it made for lining up the valve nozzle to the burner easier) from the inside, 3 wires attach on the side towards the stove taking one wire from the old valve and putting it on the new valve in the same place. Everything went back together just fine, I did have some problem with tightening one of the two gas lines for the output and found I just had to keep tightening it a little until there were no bubbles appearing when I applied soapy water to the connections, other than that it was very straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Oklahoma City, OK
- Parts Used:
- 814381
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Missouri Valley, IA
- Parts Used:
- WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
last oven bottom was ruined by melted and burnt plastic
took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!