36273485893 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Huntington Woods, MI
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not light-element glowed
First I removed the botoom drawer.
Second, removed three 1/4 in (head size) screws and removed the reflector pan from the bottom of the oven.
Third I removed the three racks in the main part of the oven and then the two slot head screws that retain the oven floor. I then removed the oven floor.
Four, now that I had access to the ignitor, I removed the two 1/4 (head size) screws that mounted the ignitor to the burner.
Fifth I disconnected the wire plug which is located in the lower section of the oven. I was unable to route the wire with it's connector on out of the oven, so I just snipped the wires and took it out in two pieces.
Installation was just the reversal of this with the obvious exception of snipping the wires. I was able to route the wires differently so that I did not have to pass the connector behind any restrictions.
Finally afte all was reassembled, I did an ops check and everything worked just fine.
Second, removed three 1/4 in (head size) screws and removed the reflector pan from the bottom of the oven.
Third I removed the three racks in the main part of the oven and then the two slot head screws that retain the oven floor. I then removed the oven floor.
Four, now that I had access to the ignitor, I removed the two 1/4 (head size) screws that mounted the ignitor to the burner.
Fifth I disconnected the wire plug which is located in the lower section of the oven. I was unable to route the wire with it's connector on out of the oven, so I just snipped the wires and took it out in two pieces.
Installation was just the reversal of this with the obvious exception of snipping the wires. I was able to route the wires differently so that I did not have to pass the connector behind any restrictions.
Finally afte all was reassembled, I did an ops check and everything worked just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from EL SOBRANTE, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas Range oven not heating/replaced new heating element
Removed oven shelves, removed lower cover, removed heating element, removed lower drawer and unplugged element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from Lebanon, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven wouldn't turn on
To get to the element I had to remove the lower cover from inside the oven.
After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.
Installation of the new one was simply the reverse.
Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.
The oven now works as it should.
After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.
Installation of the new one was simply the reverse.
Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.
The oven now works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from LIMA, OH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wanted new burners for 24 year old gas range.
Simply took out old burners replaced them with new burners, no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from MUNDELEIN, IL
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners were old and dirty
Simply removed old burners. Placed leveling nuts in place. Replaced new burners in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from ONTARIO, CA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One burner went out
All I did was remove the old burner and put the other one on. Took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherri from MORGANTOWN, WV
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner could not be cleaned any more.
Just lifted off the old burners set on the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Brooklyn, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Stay Lit/Smell Of Gas
The repair was pretty straight forward. I simply removed the old igniter, then I snipped the wires. Using the included wire nuts I spliced the old wires with the new. The longest time was spent looking for my wire strippers. I must say that the customer service was very quick and responsive. I received the part but it was broken. One call to customer service and the new part arrived the next day. Great job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICK from SAN JOSE, CA
- Parts Used:
- WB27K10141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
failed oven controller
Removed screws to back plate, unplugged, removed controller and installed new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doan from Flushing, NY
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner did not light
just lift the cover and put it on.less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from Miami, FL
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracks in the bruner due to corrosion
I bought a new Doble Burner assembly and replaced the old ones.
Piece of cake.
Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Houston, TX
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
old burners were rusty and broken
I just lifted the old part and dropped the new one in. Everything fits perfectly. The new flame is a beautiful blue color.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hyojin from Monmouth Junction, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The pipe that carry the gas to the ignition part was damaged, therefore the burner was not lightening up.
Just have to remove the old kit and replace it with the new one. No tool required.
Was this instruction helpful to you?
Thank you for voting!