9117360190 Kenmore Range - Instructions

Lifted door off the front of stove, real easy, but heavy, took out old hinge, and replaced with new hinge, I just looked where everything was before, I replaced with new, replaced door back on, and I was finished.

I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.

I followed the instructions of a PartSelect.com customer that was posted on the website. The instructions were great and the repair only took 15 mins. Before I found the PartSelect website I called the dealer who we bought the stove from and they wanted $ 250 for the repair. I went on the PartSelect Website and received the parts within 2 days.
Total cost $ 59.65 thru PartSelect. Thanks PartSelect--Great service and Great website

Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.

took off the door it should be very simple by opening the door just a little bit then pull up the door take out the shellves than take of the bottom of oven usualy there's 2 cap screws in back holding it down then take out the drawer from under the oven & unscrew the bracket that holds the flame pipe from underneath also unscrew the screw from inside the oven the holds the actual flame pipe in front next to the door then unscrew the old igniter from the pipe snip the old wire going out from the igniter & strip it a little & connect the new igniter put on the ceramic cover supplied together with the new igniter connect it back to flame pipe put everything back together you should be done. But make sure the wires are pushed down to underneath as much as you could also when you put back the gas pipe the wire should not be in the way underneath the oven

After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!

I changed out the old ignitor with the new one. New ignitor fit perfect on old mounting bracket. Attached the two wires and that was it.

It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I have never had parts come that quickly.

Removed the oven door and the bottom plate. Remove existing igniter by cutting the wire and unscrewing two small bolts. The installation of the new part is the reverse.

The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best

I only wish I would have taken the drawer out first to get at the wire connections. Instead I tried to get at them by trying to remove all the layers of sheet metal at the bottom of the oven - to no avail. Once I took the drawer out and saw the connections and bolts to remove that held the igniter/gas diffuser there was no problem. The new igniter does not come with the connectors on the ends so I simply cut off enough wire from the old one and used the wire nuts that came with to splice the wires. Simple reconnect and now we're "cookin' with gas" again.

Remove oven door,just open slighty and pull door up no tools.Take oven draw out.Remove oven floor held by two nuts in rear.You will now see the igniter,remove two screws holding it and the one screw holding the long tube at the front.The best tool I used was 1/4 drive socket set with a 6" ext.I did'nt need a new bracket that came with the part and I cut the old igniter wires and wired in the new one because it had a special connectors.If your are a handy person,its EASY.

1.Took out the metal pan.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.

Replaced the oven igniter

Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.