6654558994 Kenmore Range - Instructions

I removed the two screws for the bake element, diconnected the two wires attached to the bake element. I then reattached the wires to the new bake element, secured it with the two screws and I was done. It took five minutes and the oven works like new.

1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!

simple replacement

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

The repair was easy. I turned off the power to the oven at he curcuit breaker. Using a phillips screwdriver, I removed the 2 screws that held on the old heating element. One screw came off easily. The other screw required a little WD-40 and alot of force, but I was able to get it off. I then removed the 2 wires from the terminals on the old element. Again, it required a little force and wiggling of the contact.

Reversing the process, I slid the contacts onto the terminals of the new heating element. Then, I screwed the backplate of the new heating element in place at the back of the oven with the 2 screws I had previously removed. I then restored power at the circuit breaker. The whole job took less then 10 minutes.

Unscrewed two screws, pulled the element out of the socket, pushed in replacement element, screwed in the two screws--done!

Unplug oven unit from outlet or flip the breaker to disconnect the electricity. Used screwdriver to remove face cover, pulled wire connections from posts of old bake element. Attached wire connections to posts of the new bake element(they just slip on the posts). Aligned the face cover flush with the oven wall and replaced screws to hold cover on. Reconnect electricity and ready to bake. It is very simple.... We were very pleased with how quickly the element was delivered after ordering it.

I just removed two screws and disconnected the push on clips I then cleaned the botton of the oven and replaced the element. And it works just like new.

removed racks and door (could have left door on but made it easier to reach screws) removed 2 screws from old element unplugged the 2 wires and reversed process for new element.

I unscrewed the two screws holding the element in place and disconnected the two wires. Removed the element from the oven and replaced with the new one. Plugged in the two wires and replaced the two screws that secures the element to the back of the oven. Turned on the oven to test and turned back off when satisfied everything was O.K. Easy job.

Removed 2 screws on heating element mount plate. Pulled out heating element 3 inches and used needle nose pliers to remove the 2 connector clips. Reconnected connector clips by hand to new heating element. Put heating plate back into original position and reinstalled 2 mount screws.

Funny, I suppose. We decided to buy a new stove given the old age of the old one. Problem is, on delivery day it wasn't delivered and we discovered that there wasn't even one in the warehouse. At that point we got ticked and decided to look into the problem. The website led us right to the problem. We ordered, the part arrived the next day and the replacement was simple. Just unscrew the holder inside the over, unplug the old element and plug in the new. I needed needle nose pliers because one of the wires slipped behind the insulation. We also bought a thermometer and found that the calabration was right on the money. Happy campers... we saved $400.

Found breaker box and shut off power to stove, Check to make sure you turned the right breaker off before you attempt to put you hands in it, also make sure all the switches on the stove are in the off position . Open Oven Door, I used a Phillip screw driver to remove the two screws holding the Bake element in place . pull out to reach wire connections and gently pull connectors from element. Remove the old Bake element and Install the New one,by reversing process in removing the old one. after you have it back in place turn breaker back on at breaker box turn oven control to Bake setting, turn Oven Temperature control to around 200 degrees and Element should began to glow bright orange, job complete, it's that easy!~

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
reverse to install.
It was great to find a place that has the parts you need, and supper fast delivery service.

Thank you Ed Andrews
sound, lighting, and video systems engineer.

removed the screws that held the element in place. Pulled out the element out about three inches and disconnected the two wires, put the new one in, did the reverse and done. the best part was I orderd it on line after 3:oopm on a thursday and the part was delivered by saturday morning- wow!