9114632090 Kenmore Range - Instructions

This is how I did it--but I would strongly recommend you do step 4 first, and skip step 3! Remember, because 240V circuits have 2 "hot" wires, they may be "hot" (120V to ground) even when switched off!

1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.

AMAZING SHIPPING.Ordered on Friday,received saturday WITHOUT NEXT DAY COST.Amazing,worked perfect.

orderd a replacement part. recieved it two days later then that evening installed it. there was a video online to show how to replace it. very useful if your not a do it yourselfer.

I went on-line, found Partselect.com, they gave me the part number, showed me a video on the repair details, shipped the part overnight, and within ten minutes of the arrival of the part, I was up and running. EXCELLENT SERVICE! Thanks for saving Christmas at our house!!

You literally saved our Christmas from a disaster! Four days before Christmas our bake element gave out and we discovered it had split. We found you on the Internet, ordered the part, and prayed you would deliver as promised. We received it the next day, as promised, and in time to cook Christmas dinner. It was a snap to install, literally took five minutes. Your service, response time and instructions were perfect. Keep up the good work!

Watched youtube....

We were able to purchase the part and replace it for under $25. We took off the oven door and installed the new element in under 10 minutes.

Very easy repair. Part came wrong the first time (my fault for ordering the wrong one). Called and ordered the correct one after a closer match to the original part. Delivered much quicker than promised (one day) and installation very easy. Will use this site for all future repairs.

Well...you'll notice in other tools I put Tweezers. Now you really don't need tweezers if you do it right in the first place. Here's what I did: 1) unscrewed the nuts that hold the element in on the back of the unit. 2) Then pulled the terminals out of the holes in the back of the oven. OOPS...there were sparks as the right terminal wire hit the metal frame of the back of the oven. Scared me. I jumped. the terminal wire burned/broke off and fell back into the hole. Yep...Too late I remembered that the VERY first step of this repair is 1)CUT OFF THE POWER TO THE OVEN. I repeat...THE FIRST STEP IS TO CUT OFF THE POWER TO THE OVEN. I couldn't reach the wire with the needle nose pliers so I had to go get the tweezers. Couldn't see the wire but I just put the tweezers in about two times and it finally caught on the wire and I was able to pull it out. Luckily the terminal end was still connected to the wire so I didn't have to replace it. From there it was 3)remove the old terminal posts from the wires (used the needle nose here to wiggle the ends off - been on a long time), 4)insert the new ones, 5) push the terminal posts back in the holes, 6) screw the nuts back on, 7) bake the cornbread. A very quick job -- plus the element from PartSelect was almost half the price of any other I found (due to this I was able to upgrade the shipping a little to get it sooner and still saved money over any other price I found. Just remember to CUT OFF THE JUICE BEFORE YOU START this repair and it will be done in 5 mins or less.

I actually don't remember if instructions came with purchase. I have purchased appliance parts from here before and they did on previous times. I watched a couple of YouTube videos because I'm a visual guy (as I think most guys are) and the only difference between my reality and the video was I had nuts holding the element in place and the video had screws holding it in place. Extremely easy!! TURN OFF POWER TO STOVE.....PLEASE. Confirm power is OFF (clock not working...range wont turn on....something like that) Take oven door off hinges (mine just slid off without any problem). Remove defective element from oven. In the back there are two screws or bolts, take them out. SLOWLY pull old element out. Be careful and look for the insulation that will try to come out of the hole and watch for the wires that are attached to the element. The wires will come out far enough for you to work with them (about 6" or so). Be very careful NOT to jerk wires through holes too much or damage them. Remove wires from element. I used two pliers, one on element and one on wire crimp...I also sprayed wd40 on the connection prior and let it set for a short time before to loosen it up. Once separated, discard old element. Get new element and reverse the process. I reconnected wires, making sure to put them back in the exact same side they came off of. Ease the element power prongs back through the holes (VERY CAREFULLY, DON'T RUSH AND TEAR IT UP). The new element will fit exactly where the old one came off and just put the screws or bolts back in place and be VERY CAREFUL NOT TO STRIP THE SCREWS OR BOLTS. Turn power back on at breaker and turn on oven to check and see that it works. It should work great. This is the second part I've purchased from these guys and both jobs went flawlessly. I HIGHLY RECOMMEND these guys...plus it's almost the only place I could find to get the parts, but still they are great.

unscrewed it unhooked the wires and replaced with new part

Removed oven door & shelves. Removed the 2 mounting screws & compared parts to verify I ordered the right one, then plugged it right in! Managed to drop & lose one of the screws while re-installing them. Got a stainless sheet metal screw from the hardware store that fits, but will probably order an exact replacement because the size & thread are slightly different. All in all, other than losing the screw, it was a quick, easy task.

Remove the oven racks, remove the two retaining screws, unplugged the wires. Install wires on new bake element, insert element into opening, install & tighten retaining screws, replace oven rack's & there you have it.

First - really check that the part you order will fit. Our oven is 30 years old and the first part we ordered was not correct, but it came the very next day after we ordered it which is amazing. We were more careful about measuring for the second one and it came almost as quickly. It only took a few seconds to unscrew the old element and then reattach the wires to the new one and screw it back into the oven. Very simple. I highly recommend PartSelect.

I had grease on the baking element when I turned the oven on. I thought it would burn off, it caught fire and destroyed the baking element. I ordered a new element, it came within two days. I didn't wait for my husband to come home. I got a screw driver, took off the screw, used pliers to pull apart the old baking element from the wires. I did this carefully , our oven is old and the element was not pulling away easily. I inserted the new element, put the screws in and it worked perfectly! I was very proud of myself but the truth is that this is a simple job.