79079913302 Kenmore Range - Instructions

Removed old element with a nut driver, 2 screws. Disconnected electric wires on element, being careful not to let the wires slip into the back of the oven. Connected the wires on new element, lined up holes with holes on oven and screwed in 2 screws with nut driver. Done!!

using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine

turn off power to oven at breaker box
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on

Repair was so easy, Just remove the two screws one on each end of element slowly pull element towards you till you see the ends. Carefully
unplug the wires and then reinstall the new one and put screwes back in and you are all done

The directions have been stated many time and they are quite simple. Take out the two screws, pull the element so the wire connections come through into the oven. Disconnect the element at the wire connectors and replace. This is a dirt easy job.

The only real area for a potential problem is pulling the wire connectors through into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.

I removed the 2 screws, making sure not to drop the wires attached. Took off old wires ,then put new wires on new element, screwed it back into place and it was working. sooooo easy!!

Very quick and easy fix. Used a nut driver to unscrew the bolts. Pulled it out and disconnected the two wires. I was very happy with the wonderful service we received from Partselect.com. I ordered the part Sunday evening and the part was here Tuesday by noon. I payed regular shipping charges. What a pleasant surprise!

Take out 2 screws disconnect the wires one on each side removed element recoonnected the wires put the 2 screws back in . Also I did flip breaker off while working. When I turned the oven on I noticed it gets bright red almost instantly. I dont remember my old getting red at all. this tells me it probably needed changing a lot earlier. I ordered the part sunday nite it arrived wednesday at lunch.I will definetly use this co again.

Unplug the oven, open the door, take the screws out of the back wall that hold the small brackets which hold the element. Pull the element out of the wall, and pull a little of the wires with it to grasp easily. There are square nut screws, so you need the appropriate tool. Unplug the old element from the wires, and plug the new one in. Screw everything back together! This was a very easy fix!

Just followed the same instructions that the other people did when replacing this element. Was very easy to replace . Just turned off the power , rwemoved the two nuts , pulled the wires out about 3 inches and unpluged old one and pluged in the new one, replaced the nuts and volia ,DONE

Very simple, 2 screws, replace element, put screws back into place. The BEST thing... ordered on Tuesday afternoon, received on Wednesday afternoon, and Thursday was New Years day. This has been the best service, from any parts company, that I have ever ordered from. Keep up the good work!

i called Sears and ordered the element and they charged me 16.99 plus the part to ship the next day. after 1 week i called them and they said the part was on backorder. i then check with them each week almost a month and the part was still on back order, I asked if they could fix it faster if they came to the house, they informed me it would cost 65.00 for a repair person to see what part i needed and after that they would schedule m e for a repair when the part came in. meanwhile i could not use my oven. i happened to go on line and came up with your web site. i ordered the part and 2 days later my son installed it. my oven works great . your company is awsome.

I was getting an error code every time I turned my oven on. After a Google search I discovered it was a faulty oven temperature sensor. This website is awesome because it has a video showing how to install

I flipped the 220 circuit breaker to shut off the electricity. I unscrewed the old element (2 screws). One problem I ran into was that there was insulation packed tight around the old wire, so when I went to pull it out one of the connectors came undone. So I had to take the small plate off the back of the stove and fish the wire back through. I connected the new wires and screwed the element to the back. I only needed a square head screw-driver for the whole job. It would've taken me 5 minutes if I wouldn't have had to fish the wire back through. Still, it only took around 20 minutes and was really easy. The element cost me less than half of what an appliance repair shop charged. I'm a woman, and I've never attempted anything like this before but the video made it so easy to do! Thanks for saving me a bundle of money!

Using small square tip screwdriver (#1 if my memory is correct), removed two screws at rear of oven pulled old element carefully by pulling, removed wire from each side, attached wires to new element, slid to back feeding wire back where they had been, put screws back in, tightened and viola, stove working great. Approximate time to do job, less than ten minutes!