3627586691 Kenmore Range - Instructions

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

On each side of the door at the top you will find an allen screw, remove those to remove the handle assembly. On the inside of the door, you will find two more silver allen screws, these release the glass frame. On the flimsy part that seperates from the main door frame, there are two small brackets that hold the glass panel. Remove those using a #2 philips head screwdriver, then using a flat head screwdriver, carefully pry out all the ramaining glass shards. The glass frame will be very wobbly, this is a good time to have a friend around. place the new glass panel in the bottom slot first, then just hold it up, with a helper on one side, and reinstall the top brackets. These fit tightly on the glass, so expect to have to push a bit. now reinstall the screws, fold both parts together, use the silver screws to reconnect the glass panel assembly to the door frame, and reinstall the handle. Now you have a nice new door front!

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

First remove the broiler drawer. I laid on my side and reached into the oven to do the work, I first removed the one screw holding the splash plate (in the rear) and lifted the plate out. Then, removed the two screws mounting the ignighter to the burner base. Cut the wires on the old ignighter about half way between the connectors on the safety valve and the ignighter. I used a utility knife to strip 3/8" of the insulation on the wires still connected to the valve. Then, mount the new ignighter. Route the ignighter wires behind the gas tube. Use the enclosed ceramic wire nuts to connect the new ignighter wires to the wires still attached to the valve. Push the wire nuts into the hole behind the valve. Reinstall the splash guard and broiler tray.

Mine was simple, remove the existing burner pans and replace with new burner pans. I would definitely order from PartSelect again should the need arise.

Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.

Removed the screw from the broken piece and put the new piece on and put the screw on.

I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

This was a real easy repair. The key is to remove the door (by lifting straight up) and remove the bottom drawer. Then take all the trays out of the oven, using a screw driver remove the bottom pan that hides the burner and igniter. From underneath the oven (ie drawer space) use a screw driver to disconnect two screws that hold the burner assembly against the back wall of the oven. Then remove the one screw from inside the oven that holds the burner assembly (its close to the door area). Unplug the two igniter wires from underneath the oven and then lift out the entire burner assembly. Take off the two screws that hold the old igniter to the burner and replace with new igniter. Make sure you mark the wires when you remove them because you need the connectors on the end for the new wire. Then give yourself plenty of wire, cut the old wire off the old igniter and using the provided wire ties join them to the new igniter wires and reconnect everything. Sounds complicated but it took me about 20 minutes and its really an easy repair. Good luck.

removed old pans, cleaned up stove, replace pans and now the stove looks brand new.
thanks part select for the great pricing and superfast shipment.

layed the range on its side and removed the gas valve installed the new valve leak checked and tested works like new. Great service and parts availability, shipping was fast.

STOVE Much easier to perform than expected. First, pull the plug. Second, lift door off hinges and remove bottom storage door. Then remove bottom tray (2 thumbscrews) and the head spreader below that (1 screw). Now disattach the two wire nuts that attach the igniter to electric (from bottom, where door was). I guess this has been changed once. If it had not been, might have had to cut these lines. Then, back inside the stove, remove the flame delivery tube or whatever it's called. It kind of twists as it pulls up. From there, it's easy to disattach the igniter with a wrench and then reassemble all in reverse order. Hardest part was getting one of the wire nuts to take. One of the replacement ones just did not grab, so reused one of the preexisting.
OVEN Only hard part was getting the stovetop to release. Take off all the burner guards and such. Then lift the top slightly to locate the two push clips. Push each back in turn with a screwdriver, and this releases the stovetop, which rises up until it rests on two rests. Piece of cake to remove th electrode and attach new one.
All working fine!

Replaced old with new.