91192481992 Kenmore Range - Instructions

It was just a matter of removing 5 screws that attached the broiler coil to oven top. Then carefully removing coil so as not to cause wires attached to fall into the back of the oven. Needed an extra pair of hands to hold coil while i guided the wires back thru the opening. All that was left to do was to secure the broiler coil to oven. All completed in less then 30 mins. A lot easier then originally thought. And, a lot cheaper then getting a repair person to do the job.

First cut the power at the breaker and then removed the rear panel of the range. Then removed the two retaninig screws in the oven and then unplugged the old element in the back. Cleaned out the molten metal and remains of dinner and installed new element same way the old one came out and voila, oven is back in operation.

unplug it and plug the new one in

Ordered the part, it arrived and 5 minutes later it a complete installation

very easy and clean.

standard procedure, very simple

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.

I ended up having to re-move the back panel on the stove to access one of the wires, so that I could pull the hot wire back through the inside of the oven. The connection to the bake element was then made simple and easy. My time lost was removing the back panel and re-installation. I can not complain about the repair problem. I saved at least a couple hundred bucks. So that's my story. Thanks for the response in expediting my order of the exact bake element.

first pull the range out and disconnect power cord
remove back cover (5 screws)
Open oven door and remove racks
remove (2 screws) that secure bake element
pull off 2 wires
put new element in replace 2 screws
from the back of range plug the 2 wires to element
replace back cover
really easy

Using a set of nut drivers, I unscrewed the element from the back of the stove, I unscrewed the thermometer, and unscrewed the brackets holding the element to the top of the oven compartment.

After the element was free, I pulled it out of the back of the oven, exposing the wiring. Using pliers, I disconnected the two wires, retrieved the new element, and re-connected the wires to the new element.

I reconnected the thermometer, pushed the element back into the oven, reattached it to the back of the oven and the brackets to the top of the oven compartment.

Mice took over trailer, after eliminating mice, and cleaning oven and range thoroughly, I noticed that the only place the mouse urine smell was still coming from was the vent tube. Noticed soiling around tube where it went through and into oven. I removed the center rack, layed some foil to catch any debris that may fall from the tube when it is removed. I removed old vent tube simply by removing the two nut screws on the roof of the oven. I had to pry it out a little bit. I then cut out and soiled insulation with razor knife, I inserted the new vent tube from the inside, and replace 1/4 nut screws and tighten.

The element ignited and burnt like a sparkler. I unscrewed the bolt/screws holding it in, and pulled like I had on older models. The clips holding it didn't come undone, but the wires hit the side causing a huge flash. It was still hot, even though it wasn't turned on. You need to unplug the oven, or turn off the breaker. I unplugged and took the back panel running down the middle off (4 screws), and undid the clips. Putting the new one back in was easy. Insert the element ends through their places inside the oven. Screw them in place. Hook the wire clips on in back, and replace the back panel. Installation took less than 5 minutes.

burner went out Thursday evening, ordered new burner at 8:30 pm, new burner was delivered Saturday afternoon, removed back panel from range, removed burner, replaced burner, re-installed back panel. Took less than 1/2 hour to replace. Hardest part was finding the correct size socket.(ALL WITHOUT HELP FROM HUSBAND.) Thanks so much for prompt delivery.

Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one

Took out the nuts that held the old element, removed it, put
in new element with tightened nuts...and it didn't work.
We took off the plate on the back of the stove, found the
element contacts protruding through, attached them to the
wire connectors that were close by, and it DID work. We were thankful it turned out to be easy!