79061750106 Kenmore Range - Instructions

We moved into our townhouse about 6 yrs ago. During the home inspection we checked the range and saw the Red light come on when we turned on each burner. After moving in we realized the large back burner did not work. The light came on but the element never got hot. I of course replaced the element but that did not work. Several years passed and we just ignored the issue. We just got by with 3 burners. Lately we realized how much easier it would be to have all four burners working. Knowing that we will be selling our townhome soon we figured we should either fix the problem or replace the range.

I didn't want to call a repair man because I didn't want to be charged a $150 to have him come out and they to pay extra for parts (and of course a 2nd visit). So I went to www.Partselect.com and typed in the model of my range. Found the diagrams for my range and saw that from the switch ran a pair of wires to a Universal Receptacle (aka Terminal Block Kit). I figured since the Red light turns on when I turn the switch on it has to be the Terminal Block.

I ordered the part from www.Partselect.com ($14.00 including shipping) and replaced the part. The burner still would not get hot. I decided to test the switch. I removed the Control Panel cover (which is secure by 2 screws just below the digital clock). Once the cover was off, I saw the Blue wires going from the switch to the Terminal Block. To test the switch, I disconnected the two Blue Wires from connectors H1 and H2 and temporarily connected them to H1 and H2 of another switch. Sure enough, when I turned the other switch the element got hot.

So I placed another order from www.Partselect.com for a replacement switch ($50 including shipping). When that part came, I flipped the electrical circuit going to the range. I then removed the Control Panel cover again. With the new switch in hand (holding it near the old switch still attached to the Control Panel, I used the pliers to pull out each wire from it's connector and place it to it's corresponding connector on the new switch. Once all the wires were connected to the new switch, I pulled the knob of the switch off then used a phillips screwdriver to remove the two screws holding the switch to the control panel. I replaced the old switch with the new one put the screws back in, replaced the knob. Turned the circuit back on and tested to make sure that the element got hot. When it did, then I replaced the Control Panel cover and enjoyed a nice dinner that was cooked in less time than we're accustomed to because of the new burner. So I spent a total of $64.00 to fix our range. Less than half the amount I would've spent if I called for a technican. And far less then buying a new range.

Partselect is a great resource for information. They have diagrams and schematics available to view and/or download. And when ordering it's a snap because there's an "Add to Cart" button next to each part it lists. So there's no confusion. I've already recommended Partselect.com to about 5 people. And will continue to do so!!

The old glides were broken off so I didn't know I needed these glides until I saw the parts section of the Manuel. When they arrived I snapped them in with no effort at all.
P.S. The shipping is fantastic here......i ordered on Monday received them on Tuesday. Now that's shipping:>)

The two back door glides were missing and broken (one of each), and needed to be replaced. Finding the parts online was MUCH easier than I expected,and the repair was remarkably simple. Parts snapped into place, the drawer had to be lined up, and it slid right into place. Very easy!

Turned off power, took back off stove removed old probe.
I had to splice wires since new probe ends did not match up.
the instructions were to splice the wires. I had the breaker off for about 3 hours. this is not in the instructions, but being a widow, I had to ask a few people why it would not come on after I connected the wires.
After waiting, I turned the breaker on and my range came back on.

I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Removed the back cover of the range. Removed the knob from the front of the switch. Removed 2 screws holding switch to range. Removed wires one at a time and connected to proper poles on replacement switch and reinstalled new switch on range

Ever since we moved to this house I had used generic or standard drip pans found in any store. Needles to say they never fit properly so I always ended up with some burners tilting so my food would not cook evenly Until I decided to search for stove specific drip pans and this is how I bumped into your site. I am so happy now I can use all four burners at the same time if I wanted to, and my food cooks evenly since the burners are not tilting.

All the was needed was a Phillips screw driver. It's not difficult. Watch out because the door is spring loaded and does seperate quickly after all the screws are out. Be sure to watch the front panel, it appears to be heavy glass and can come out of the slots during the repair. I only had to re-assemble and dis-assemble 4 times before I got it right but it's still fairly easy to do if you take your time.

I had to replace the switch in the back of the control knobs. I was very grateful to the female phone attendant who answered my call. Since my part number had switched a few times, she took the time to reverify the "blueprints" of my machine with the parts carried at Parts Select and she helped me be assured that I was buying the correct part for my machine. She was SOOOO helpful. Will definately buy again from your store.

Pulled stove away from wall until I could access behind it. Disconnected power source, used nut driver to remove 7 small hex screws with nut driver, from back cover, slide down and away. Disconnect two wire( 1 from each end of element). Open oven door, remove all shelves, remove two screws inside oven on back wall, pull out old element. Guide in new element(gently guide each end through access holes in back of oven, line unscrew holes with retaining clips, insert screws. Place racks back in oven. Reattach back panelnwith 7 screws, plug power source back in. Slide oven back into place. Done.

I disconnected power cord. Removed cooking racks. Removed element mounting screws. Removed back panel and removed wires on both ends. Pulled element out put new one in and bolted down. Reconnected wires. Put rear cover on. Plugged in and checked for correct opreation. OK!

Turn off the breaker to the stove. Very important because when you move the control panel around after removing it, you can inadvertently touch a hot wire to a grounded metal part on the stove. Remove the 3 nuts from the back of the control panel and the two nuts from under neath the control panel on either far side. Pull the control knob off by pulling straight away from the control panel. Remove the switch by unscrewing the two screws. Match the 5 wires from the old switch to the new switch by removing one at a time and paying attention to the labeling of each on both switches. Reassemble in reverse order. Turn breaker back on.

When we bought our home less than a year ago, we had three functional burners on our 40" wide 50's classic Kelvinator (not close to standard size these-a-days). After a few months of use, two more burners went out for good and we were stuck using the back left burner for all of our cooking. I opted for the premium burners and made sure to compare my terminals with the ones online to be sure they mounted the same. I removed the burners and terminals, clipped the wires going into the terminals, and removed the top of the stove. I followed the directions that came with the new terminals, pushed in the new burners and viola! All four burners now work. I gave the stove a general cleaning and now my 1954 Kelvinator looks and cooks like it is brand new. It was easily the best $109 I've spent on my home.

was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff