36272624302 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Nashville, TN
- Parts Used:
- WB13K10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Large burner wasn't lighting very quickly
Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Watervliet, NY
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Jessup, PA
- Parts Used:
- WB28K10190, WB28K10189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Bent/Broken Front Orifice Tubes
I removed the two nuts that secure the rear orifice tubes. This allowed me to lift the range top to access the broken tubes. Once lifted I removed the nuts that held the broken orifice tubes. I then connected the new orifice tubes. I removed the three(star)screws that fasten the orifice brackets under the range top. Doing this allowed me to connect the new tubes without having to maneuver them at all. I then lowered the top just enough to reattach the brackets. After securing the rear tubes I snapped the range top back into place. Just remember, if you use propane for cooking then you must remove the brass orifices from the old tubes and place them in the new ones. If you don't do this then your flame will not burn properly. Simply unscrew them from the old tubing and put them in the new tubing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Grass Valley, CA
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't heat up.
Replaced the burner and igniter after watching the repair video provided by Partselect. I was pleasantly surprised when the parts came the very next day. It was so easy and the igniter plug matched perfect. My wife wanted to hire a repair man but I did the repair and saved a bundle on the labor. I couldn't be happier about my purchase.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Louisiana, MO
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would fill up with gas before igniter got hot enough to lite it
Remove bottom drawer,open oven door,take oven racks out,use flat tip screwdriver to remove two screws in back of oven. Then remove cover over burner and igniter.Reach under oven and unplug igniter,while down there use 1/4 inch nut driver and remove two screws holding burner. Then remove one screw inside oven in front of burner. Pull burner and igniter up and out of oven.I did not unplug stove or turn off gas some people may want to,if you have to move stove out to work on it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Somerset, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Del Rio, TX
- Parts Used:
- WB16K10035
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
am still waiting for my parts-first delivery:ignitor broken. Second delivery: Ignitor missing.
could not even attemt installation due to messed up parts delivery
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FELIX from DELTONA, FL
- Parts Used:
- WB34K10016, WB34K10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip pan Replacement
It was a snap. Lifted all 4 burner grates, pulled old drip pans out, installed the new ones. Perfect fit. My mother is happy-happy. thanks Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glen from felch, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
uneven flame and sputtered, burner was not useable
Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Yorba Linda, CA
- Parts Used:
- WB29X36765, WB29K10005, WB29K10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Chipping around edges of Burner Caps
Received the parts very expeditiously(2 days from time of placing the order), and the replacing of the caps was a "no brainer".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Perkiomenville, PA
- Parts Used:
- WB34K10016, WB34K10015, WB29K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed to replace the drip pans, burner caps and grates due to old age.
After one week, the enamel on the drip pans and 1 of the burner caps were starting to wear away. They gave me a refund,including shipping and sent me replacements. They are a very reputable company.I will buy items from them again.
Was this instruction helpful to you?
Thank you for voting!