91195502000 Kenmore Range - Instructions

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

Unplugged the oven, took out old element and replaced with new element. It was really simple and easy to do, didn't even need my husband who is not mechanically inclined.

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

It took a bit of head scratching to remove the oven door. I had read another user saying he'd removed the hinge screws unneccessarily, so I left them alone. I eventually was able to locate the locks on each hinge. Once they were disengaged, it was a simple matter to lift off the door. After that, I removed all the screws (except the hinge screws) and took the door apart. Once it was disassembled, I found two loose triangular pieces, about 1 1/2" long. I later discovered these were spacers for the two top srews. They were placed on end, and the top screws passed through them. All in all, a relatively simple repair, which absolutely amazed my wife, landlord, faily, etc.

First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.

well first i came here thewn i called got my part the next day by the way paying only regular postage. it took me more time to pull the stove out and find the sockets then to actually put the element in.that took a whole 3 minutes. thanks partselect you guys are the best and i will be back.

I simply turned the power off and slide the stove forward to give myself room to get behind it and just unscrewed the cover behind the burner switchers and pulled the switch knob off then I removed the two small screws that hold the burner switch to the control panel and go to the back and pull the wires carefully and replace them on the new switch one by one and screw the new switch to the control panel and replace the back panel and done!

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

I first ordered the wrong part and had to call customer service. They handled the return and ordered the new piece beautifully!! The installation was really simple. Once I took out two screws holding the top down, I removed three clips holding the burner on then switched out the electrical leads. Put everything back and it worked perfectly!!

Replaced element control switches

Had to move the range out of its little cubby hole in the kitchen so that I could have access to the back of the range. This process probably took the longest. After that it was a piece of cake. Took about 15 minutes to complete the job. So easy, eve a caveman could do it.

Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.