79092854301 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Abe from Manson, WA
- Parts Used:
- 5304528972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner quit working
Received the new part FAST. Ordered online. Easy to plug in the new part. Will use PartSelect.com again when needed to order parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from cincinnati, OH
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
heating elements not working
prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from McHenry, MS
- Parts Used:
- 316436000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
When turning the switch on for the large eye I could hear an electrical short behind the switch.
Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on Partselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from El Paso, TX
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just had to replace the racks in the stove.
Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Dasssel, MN
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was not heating properly
I ordered the element. When it arrived, I simply removed the old one and put in the new one. However, it did not completely solve the problem. The heat is now distributed evenly, but still have to turn the burner to 7.5 to boil water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Mt. Vernon, AL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rusty worn out oven racks
Removed the old oven racks and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Fossil, OR
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced burner block
Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Sidney, NY
- Parts Used:
- 318372211
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element didn't work
I did the repair in less then 5 minutes. I took out old element and put in new one and turned it on and I had heat. Works great Thanks the part came in 2 days what a wonderful suprise that was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Kettlersville, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner burned out
unplugged old burner plugged new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Greencastle, PA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" left front surface element would no longer heat properly
I ordered the exact replacement element, and after unpacking it, it took about 5 minutes (actually,less; didn't time it), and the new element was installed and working fine.Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Fort Wayne, IN
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old oven racks were nasty!
We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Hiram, OH
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't work
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from NORTH PORT, FL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
no heat in oven
replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.
Was this instruction helpful to you?
Thank you for voting!