1037867810 Kenmore Range - Instructions

Part arrived day before thanksgiving bent old igniter back and forth till broke off then easily took out screws.Cut and strip old wire, screw on new ignighter this was tough to get a wrench on with the positioning but after connecting those wires and slappin the rest of the oven back together one turn of the temp knob told me thanksgiving was going to happen Thanks to part select I was lookin like a hero!

I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut the cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.

I removed the oven grates and removed 2 screws that held the bottom pan in the oven to get easy access to the burner and igniter. Remove 2 screws that held the burner in place. Removed wire nuts. Removing burner allowed easy access to fasteners holding ignitre in place. Confirmed that the igniter was bad by checking the continuity. Ordered part later in the evening from parts select. Part was here 2nd morning after I ordered it. Installed, and checked to make sure igniter wasworking properely. When check confirmed igniter was working, replace oven components. Saved myself $100 or more by doing it myself rather than having a repairman out.

i removed the oven door and then the lower panel.the two screws holding the igniter were hard to access, so i removed the gas rail.this made the job much easier. the advice from other people on this website was very helpful and made the repair much easier.just remember to shutoff both the electric and gas supply.

Good friend said he could do it no problem at all!!!!!

1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy

I took the old igniter out and replaced it with a new one.

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

To diagnos i removed the lower tray and could see the ignitor was not lighting like the broiler was,the same ignitor.I had the same problem as some of the other people so that was helpful.I removed bottom storage tray and could get to the wires and it was an easy fix,took about 40 minutes total.This website was very helpful also with excellent service on the parts and i saved a bunch of money!
Thanks,Gerald

First I got on line to make sure I had the right part. After it was delivered I started the project by unplugging the stove! A magnetic end for your socket device is very helpful.:-)A good alternative light source is esential to see what's going on.There is no need to pull out the stove.I then took off the oven door which is an easy process(Pull up off the hinges). I also removed the oven grates and lifted out the bottom plate which included the heat defuser.I then took out the storage drawer. The next step was to remove the rear screw and front 2 screws holding the burner tube. Then it was just a matter of pulling up on the tube and removing the screws holding the igniter.The 2 wires were then cut and the new igniter wires were spliced in with the new wire nuts that came with the package. I also used a little electrical tape to hold things in place. Then it was just a matter of replacing everything in reverse and plugging the stove back in. Everything works fine.

There are other descriptions here, but here's my story. I pulled the oven door off (pull straight up on it, it will come off) and removed the bottom warming drawer (there are plastic tabs on the outside of each side of the drawer--slide them and pull, several times on each side). I turned off the gas from behind the stove and unplugged the range, undid two screws at the back of the oven floor and lifted it forward and up. The burner is visible, but here is the hard part. The bolts holding the ignitor are underneath it and angled such that it is almost impossible to get any type of tool near them. I have small hands, and that helped. The screws are a bolt-head type or hex head, and I found that a one quarter inch open end wrench sort of fit. 6mm was too small and 7mm was too large. I managed to get the screws loosened after much struggling and manuvering, with half my body inside the oven, and once it was out, I was able to reach in from where the warming drawer was and unscrew the two wire leads attached from the ignitor to the power. They are held by plastic screwcaps. The reverse process was self explanatory, except that you should put the new ignitor in the oven and feed the wires down through the back panel, then attach the screwcaps to join the wires to the leads. Then go back in the oven and attach the ignitor, back screw first, and tighten it all the way, since you may not be able to reach it once the front screw is in. Also, use the screws that come with the new ignitor, since they are easier to start than the old ones. Tighten the screws as tight as you can get them so the ignitor doesn't wiggle, then turn the gas back on and plug it in, and test it before you put it back to gether. Mine worked, but it was a pain to do, kind of like working on an old car that wasn't designed to be fixed easily. Good luck.

FIrst, have the tools you will need, a straight ratchet screwdriver, 1/4" ratchet/screwdriver set, a 90 degree offest, some small plastic bags to hold/tape screws to the pieces you take apart, and a flashlight.

1) Turn off the breaker to the oven.

2+ 3) Take the oven door off. It simplly lifts straigh up off the hinges. ( It slides back on hinges when you're done.) Take off the botton kick plate by pulling top down. The botton in on a hinge.

4) Slide out the oven racks.

5) Take out the inside bottom cover of the oven which is inside the oven. The cover lays flat and is attached by two screws in the back inside corners. You have to lift it up/out back edge first. (Put it back front edge first, & realign screw spring clips if necessary)

6) Slide out the oven gas line/igniter cover, which is found immedicately under the oven cover, by taking out one screw front center. You will then see the igniter in the back of the oven next to the gas line. *DO NOT UNDO ANYTHING HOLDING THE GAS LINE*.

7) From under the oven, take out two side screws helping to support the botton tray, one each middle side. Then take out the two most front bottom screws. while holding the front edge up. (It will drop) Then slide it out of groves in the back of the oven.

8) Take out the inside cover (2nd botton cover) by taking out the two screws from the inside front top. It will also slide out. This will totally open up access to the igniter bracket attacked to the gas line. *NOTE CURRENT PLACEMENT OF IGNITER WIRES*

9) Take off the two igniter bracket screws. Put the new igniter in its place.

10) Cut one wire off the old igniter as close to the old igniter part as possible. *YOU WILL NEED ALL THE EXTRA WIRE* *DO ONE AT A TIME* Match the same wire position old to new, strip 1/4", twist and ceremic wire nut provided together. Do the same with the second wire.

Put all parts back in reverse order.

The broiler still worked, so I knew the issue was not with the power or gas to the oven. It was easy to remove the inside bottom of the oven to look at the igniter and burner. 4 screws hold the oven bottom in place. After the igniter was in view, I turned on the oven to see if it glowed, which it did not. 2 more screws out and the igniter was loose. The two wires coming out of the igniter go through a hole in the back of the oven to a compartment below the oven. This compartment is accessed by removing the bottom drawer and removing a panel in the lower back of the oven held in by 4 screws. After disconnecting the wires, I attached a thin pull wire to them then pulled the igniter out through the oven door. The pull wires made it easy to feed the new igniter wires through the back of the oven. The rest is a reverse of the process.

Just replaced the igniter, was pretty easy