9119330191 Kenmore Range - Instructions

Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven. I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.

I unplugged the old unit and plugged in the new one! It works.

.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.

it was very easy, a few seconds and new range for a cuople of years more!

My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.

Quick and easy, thanks!

The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best

Easy

1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two retaining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake

1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace of tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.

Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices!
Thank you,

4 screws held the cook top down, took top off exposing the burner elements, ordered the one that was bad ( could not
believe how easy it was to order from Partselect, and then how quick I received it.) Shocked myself when taking out the element, forgot to disconnect the breaker.

As others have described, the removal of the old bake element is easy, just undo screws in the mount holding it to the inside wall of oven and pull out, then disconnect wires.

The first thing I faced unique is that some of the old element melted on the walls of my oven. After scrubbing extensively, it was obvious that the majority of the melted element was permanently fused with the oven wall--although it doesn't seem to have affected oven performance so far.

Next since my range was made in 1982, the replacement bake element didn't exactly fit my unit. Several adjustments had to be made. The size and fuctionality of the new bake element matched my oven, however the wire connections and the oven wall mounting bracket and the spacing of the two ends of the element as it went thru the oven wall were very different and required extensive modifications.

I used the old mounting bracket from the old melted element to attach the new element since my oven wall opening and mounting holes matched the old element mount--NOT the new element mount. This required removing the old mount from the old element by means of a vice, hacksaw and wirecutters. It was necessary to examine the old element mount very carefully before I hacksawed it off the old element as it must be reconfigured onto the new element. It will be bent up somewhat while removing---be careful.

Then I reattached the old mount on the new element. This required carefully bending the new element ends to receive the old mount as they were spread too far apart in the new element configuration. After much trial and error bending with several types of wirecutters the old mount was secured to the new element and installed into the oven.

Now a new problem appeared--the element ends now stuck too far into the back wall of the oven, making them dangerously close to touching the exterior of the rear of the oven and remember these are bare, hot electric connections! Much time in trial bendings and repositioning of the new element with the old mount finally resulted in a successful mounting with the old mount and the new element in a way that safely kept the bare wire connections within the rear oven walls.

A final problem was encountered when the new element came with slide-on wire connectors while my old element had screws and holes to connect the wires together. I found a drill bit the size of the required screws and drilled holes in the new element's wire slide-on connectors so that I could use the screw connector system of my old element to connect my new element's wires together. It all worked and the oven is functional.

This was really easy considering what it would have cost to have a repair person come and do it - not to mention the wait time. I had to hunt around a little bit to find the right socket, but once I had that, I unscrewed the bolts in the back and slide the element out. TIP: make sure you turn off the electricity!!!!!!!!! The wires were a little stuck, but the oven is 11 years old, so it's to be expected. One of the wires came off behind the oven, but I used needle nose pliers and fished around until I grabbed it. I detached the wires, attached the new ones, turned the electricity on and it's been baking Christmas cookies ever since. BTW - the part came in 3 days. I was sooo happy I didn't have to wait for a repair person. Thanks for all of you who posted your comments online. That was just the encouragement I needed to try it myself!

Removed to screws holding the bake element in place. pulled out element to get to the 2 electrical connectors. removed connectors from old unit. connected new unit and secured with the screwes. very simple.