9114688810 Kenmore Range - Instructions

Just remove the pots and pans drawer from the bottom of the stove. Unhook the remains of the old springs from the door hinges underneath, and from the holes on the bottom of the the stove frame. Then hook up the new springs in the same holes. Then replace the bottom drawer. Very easy repair.

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

Removed the door. Unscrewed the hinge from front of oven. Took broiler drawer out. Unhooked the spring. Removed hinge. Screwed new hinge in. Rehooked the spring. Slid oven door back on hinges. Mission accomplished. Oven door works like a champ. Wife happy.

i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!

First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..

Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.

At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!

I followed the instructions of a PartSelect.com customer that was posted on the website. The instructions were great and the repair only took 15 mins. Before I found the PartSelect website I called the dealer who we bought the stove from and they wanted $ 250 for the repair. I went on the PartSelect Website and received the parts within 2 days.
Total cost $ 59.65 thru PartSelect. Thanks PartSelect--Great service and Great website

Shut of circuit breaker. Removed two screws with socket set . pulled element out about three inches, disconnected and held wires in place with clip type closepins. pressed connections onto new element , secured screws and presto... All too simple and in less then 15 minutes.
Reading previous reviews was quite helpful

first husband removed the bolts unplugged old element wires -plugged in new element wires and but in bolts - unfortunately the oven still doesn't work not sure if element is bad or wiring, need professional help

Replacement of the heating element only takes a few minutes...First, turn off the breaker/fuse to the stove, then just remove two screws , pull out the two connected wires to expose the connections, hook them up, and replace the screws to the cover plate. The connection/cover plate can be hinged or not hinged. Make sure you order the correct one. We ordered the wrong one at first, but were assisted by the returns dept. and received the correct one in 2 days. Great customer service, thanks partsselect.com!!

Removed the two screws, pulled out old element, installed new element, and reinstalled screws.

Really easy.
1) Pulled up on oven door and removed it.
2) Removed lower drawer to access springs.
3) Pay attention to which hole the springs are attached under the oven.
4) Remove spring with Needle Nose Plier. If you remove by hand, the spring will likely cut your finger....like mine.
5) Unscrew 3 screws of old hinge assembly.
6) Reverse process when placing new assembly in place.

.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.