91145569791 Kenmore Range - Instructions

First I removed the two screws holding the element to the back of the oven. When I pulled the element out I disconnected the two wires and removed the element. I found the serial / part number on the existing part and order from PartSelect. The element arrived two days sooner than expected!! Replacing the element was a bit more difficult in that I had to pull the stove away from the wall and remove the rear cover in order to pull the wires and element through the insulation in the back of the oven. Four screws held the rear cover, but once those were removed the element easily went into place and the repair was finished. Cleaning behind and under the stove took a few extra minutes but the entire repair only took about 30 minutes, plus the wait time for the part. Two tips, pliers were used to disconnect and reconnect the slip-on connectors. The connectors were pretty tight and reaching to the rear of the oven was difficult to get leverage to pull apart and reconnect. Also, the oven light caused considerable glare on my glasses so I taped the door button controlling the oven light and used a flashlight to see inside. Otherwise, a simple repair. PartSelect had the best price on the element and service and delivery were excellent!

removed two bolts on the inside of the oven, disconnected the two electrical connections in back which were a little set so I had to use pliers and removed old element. Reversed procedure to install new element.

The >15 minutes includes vacuuming out the oven.

partselect.com deliver was extremely fast and the part was packed securely. We would order from them again without a problem.

With less than 24 hrs from ordering to delivery, I was making cookies. Installation was quick and painless.

pulled stove out from wall about a foot ans disconnected the electricity cord. removed the 2 screws holding the element in place and pulled it out a bout 3 inches and disconnected the two wires. attached the new element & pushed it in place and tighrened the 2 screws. hooked up the electric power, moved stove back in place & it was done!

Unplugged the stove. Unscrewed the element. opened the rear cover to reach wires. Passed wires through the slot and connected the element. Screwed the element in place. Reinstalled the rear cover. Plugged the stove and pushed it back to place. Tested the oven, it worked.

Very simple. Two small hex shaped screws hold the unit to the back of the stove. Remove those with a small socket wrench. Rachet type makes the job easier. Gently pull the element from the back of the stove. Remove the two push-on wires from the element. They simple pull off. The elements have supporting feet toward the front. Those must be down to rest the element on the bottom of the stove. Replace the push-on wires, push the element back into the holes in the rear of the stove and screw the small hex shaped screws back into the oven wall. The job is done.

I followed the directions in the video on the website. The repair was so easy!! I simply unscrewed the screws holding the element in place at the back of the oven, pulled the wires out. This did take a little bit of time, as I didn't want to pull the wire off of the element and lose it in the back of the oven, but I was able to eventually work it free from the insulation and make the connectors visible. I slid off the old element, slid the wires back on to the new one and pushed them back into the wall of the oven and replaced the screws. Works like a charm!! I will definitely use your website for other appliance repairs!!

Pulled oven from wall, Unplugged oven from outlet, Took 5/16 nut driver pulled back cover off oven to expose the quick connect wires, Pulled wires off old element, Opened oven door took the 2 screws off bracket on back of oven, Removed old element, Put new element in place, Put the 2 wires back on, Buttoned back up check to see if worked it did ((:

Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 days. They still don't have the part. Thanks so much.

Two screws hold the element to the oven wall. two wires attached to the back of the element. very simple removal and replacement.

Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.

I removed the two screws with a nut driver, pulled the element out far enough to expose the connection point and disconnected the electrical clips. Upon receipt of the new element I did those things in reverse order and it worked great.

First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done

Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)

After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new element from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.