9114628691 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jewel from Nacogdoches, TX
- Parts Used:
- WB25T10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The temperature indicator light on the oven was broken.
I removed the control panel by removing 7 screws and replaced the light indicator and lens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Damascus, MD
- Parts Used:
- WB25T10040, WB25T10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The indicator light stopped working
I knew the lens (which also holds the light) was broken. I also ordered the light. I flipped the circuit breaker, raised the stove top and removed the 6 nut-head screws holding the cover plate. A nut driver would have been helpful, but I got by with a 6" crescent wrench. I removed the cover. I unplugged the two wires from the old light and plugged in the new one. I inserted the new lens and slipped the light over it. I flipped the circuit breaker on to make sure it worked. After flipping the circuit breaker off, I replaced the cover plates and the screws and lowered the stove top. I flipped the circuit breaker on. It worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Hindman, KY
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner wouldn't operate
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel
Knott County Housing Authority Maintenance Personnel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry J from South Haven, MI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven stopped heating and element appeared broken
The customer service rep was brilliant in finding the
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from assumption, IL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake element burnt into
repair went fine, real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Westerville, OH
- Parts Used:
- WB56X1901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inner glass of slide in range was cracked needed replaced
Removed door from Oven.
removed screws from several components comprising the door and separated pieces.
Removed broken glass.
Prior to putting back together I took advantage of the convenience and used oven cleaner to clean inner portion of door. Installed new glass.
Reassembled door.
removed screws from several components comprising the door and separated pieces.
Removed broken glass.
Prior to putting back together I took advantage of the convenience and used oven cleaner to clean inner portion of door. Installed new glass.
Reassembled door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CLAY, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
The phillament ends were pointed straight and the one I removed from the oven were bent in an angle .
Bent the tips so the phillament can fit inside the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Rockport, ME
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not get to temperature...200 degrees max
Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Thornville, OH
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Heat element burned out
First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Gulf Breeze, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't heat - wire not exposed
Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Indian Harbour Beach, FL
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Halogen element staying on
removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard L. from Clear Spring, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No heat lower bake unit / Broiler unit heats ok
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Houston, TX
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
oven coil caught on fire and broke in half!
I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorced mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- allen from MT. AIRY, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake element was broken
i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!
Was this instruction helpful to you?
Thank you for voting!