9114658814 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marion from METHUEN, MA
- Parts Used:
- WB2X9719
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Single Heating Element Support Clip was needed to hold up the heating element in the oven. Old single heating element support clip broke and came out of the hole.
Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lorita from bend, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
my lower oven heater went out
i was really pleased getting the order from partselect. i had torn my oven appart and knew i needed just this one part i came home and ordered it from parts select and actually got the part the next day.... very nice.... so pleased
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Oxon Hill, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element burnt out
remove two screws slide out. slide new one in. put two screws back. done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from COPAKE, NY
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Swicth Stem Broken
Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]
Was this instruction helpful to you?
Thank you for voting!
Burners wouldn't sit right in drip pans. Melted a plastic container on a burner.
Make sure all burners are off and cool to the touch
Lift up on the burner coil and pull to the side
Lift out the drip bowl
Gasp at how dirty it is
Dispose of dip pan in recycle bin
Wash the gunk off your stovetop, then wash your hands!
Replace the drip pan so that the hole is over the plug in area
Replace the burner coil by poking it into the hole and fiddling around with it until it engages.
Push it firmly into place.
Admire your work, go fix a cold drink and put your feet up
Feel good about your home repair skills!
Lift up on the burner coil and pull to the side
Lift out the drip bowl
Gasp at how dirty it is
Dispose of dip pan in recycle bin
Wash the gunk off your stovetop, then wash your hands!
Replace the drip pan so that the hole is over the plug in area
Replace the burner coil by poking it into the hole and fiddling around with it until it engages.
Push it firmly into place.
Admire your work, go fix a cold drink and put your feet up
Feel good about your home repair skills!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SALISBURY, CT
- Parts Used:
- WB2X9719
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The old single heating element support clips came loose over time.
I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from KNOXVILLE, TN
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two large burners wouldn't heat or would smoke even after cleaning
i really wanted a new stove, but budget wouldn't permit; so just had to insert the new ones and they work great with level cooking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from N CHARLESTON, SC
- Parts Used:
- WB17X5095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no burnt wire
Replace part an wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ervin from Milford, DE
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
infinite switch would not shut off at times.
First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hedgesville, WV
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element clap broke off
All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from VINELAND, NJ
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Electric Burner Control Broken
New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PLANO, TX
- Parts Used:
- WB21X36771
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Old infinite switch WB21X36771 broke...heating element stopped heating
1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Lexington, KY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Heating element had shorted out and broken.
Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
oven door jammed,could not open it
Removed old hinges and installed new hinges.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Dayton, OH
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Lower heating element cracked
Followed the video directions on your website - GREAT INFORMATION. Everything went very smoothly It took me longer to find my work light (after turning off the electric to the oven) out in the garage than it did to complete the repair!! SUPER PLEASED - WOULD NOT HESITATE TO RECOMMEND THIS COMPANY TO ANY DIY ADVENTURER!!
Was this instruction helpful to you?
Thank you for voting!